Glock34Guy83

$408 shipped aimpoint micro h1! I just bought one myself. http://palmettostatearmory.com/aimpoint-micro-h-1.html

https://dawsonprecision.com/make-ready-sale/ CMC flat triggers for 134.99, http://www.rainierarms.com/cmc-trigger-single-stage-flat 30% off Geissele stuff, http://www.primaryarms.com/geissele-automatics/c/brand_1001_74/?kc=HOLIDAY&utm_source=bronto&utm_medium=email&utm_content=BANNER_2&utm_campaign=15-11-Ad4_Black_Friday&_bta_tid=3.cFU.B_NFlw.Ej7J.Ary0Rw..A3uWaw.b..l.BStr.n...DVzjlQ

I'm new to the single stack division. In fact I haven't even shot a match yet. That being said I want to start getting more and more into uspsa and I'm going to devote at least a year to shooting nothing but single stack in uspsa. My question is, can I deepen the cocking serrations on my 1911 slide and add forward cocking serrations? Or say I wanted to have the slide milled for a bomar type adjustable rear sight instead of the factory Novak style that's on there? Or is any kind of slide modification against the rules? Any input would be greatly appreciated.

Thats why I never leave a gun in my car overnight or for any extended period of time. It's just not worth the risk. Sorry for your loss and I hope it gets recovered quickly. Best of luck.

I have a 9mm RO and it's been flawless so far. Even after I had the slide,barrel and bushing nickel boron coated it still functions 100%. I use the trip research mags and with the dawson no gap ice magwell I had to sand the top of the basepads to help them seat easier with a fully loaded mag.

Col?

What is you COL for that load?

I tried 5.0 grains of N350 with a 160 grain bayou bullet at a o.a.l. of 1.55 and I had a bunch of yellowish unburnt powder left in the cases. I was getting 1.5 - 2.5 inch groups at 15 yards standing out of a 4" 627 pro. I'll be trying a different load with bullseye powder tomorrow

I hate to bring up an old thread but I have 4+ pounds of N350 and I was looking around at load data and I noticed that it can be used in 38 special loads using 160 grain projectiles. http://www.vihtavuori.com/en/reloading-data/handgun-reloading/-38-special-.html It looks like even at the lowest recommended charge that it gets the bullet moving way over minimum power factor. I'm thinking about trying to work up a load using N350 to see if it's would be an accurate load or if it's a waste of time. Has anyone tried this before and if so any results? good or bad?

Matts2k that looks amazing. I love those grips. Who makes them?

My new to me CZ 75 Accu Shadow Lite. Now I know why there is a whole section just for CZ pistols. This thing is amazing.

Thanks I will load some up with your info and chrono it and report back.

I have about 4 pounds of N320 left. I normally use it for my 9mm loads but if you don't mind sharing your load data I will give it a shot.

Bullseye is the powder I have the least of but I'll give it a shot. I loaded up about 50 rounds tonight with 4.0 grains of Win 231 with an OAL of 1.445. According to the reloading book that I have on hand it should roughly put me around a 130 power factor. I had some loads that had 3.7 grains of win 231 and I was only getting around a 102 power factor. I think I was not crimping enough. I increase my crimp and upped my powder charge and I will chrono these new loads this coming weekend.

I'm steadily getting more and more into shooting my 4 inch 627 pro series. I have 3 choices of powder to use and they are VV N320, Bullseye and Win231. I currently have 158 grain round nose flat points from Xtreme. I am going to be switch to 160 grain RN from bayou or black bullets. So my question is, Does anyone have a good load with any of those powders to make power factor and would you mind sharing it? What powder and how many grains? What length are you seating too? I figured I would post here instead of the general reloading section because this is for a revolver. Thanks for your help.