Jump to content
Brian Enos's Forums... Maku mozo!

matt7184

Classified
  • Posts

    158
  • Joined

  • Last visited

Everything posted by matt7184

  1. Roger, I'll give that a try. Thanks!
  2. Picked up two samples to try out. Canik nailed the value and trigger on this gun. Very impressed. Ran a few hundred rounds of Magtech 115gr FMJ, CCI Blazer Brass 115gr FMJ, Winchester M1152 115gr FMJ without issues through both guns. When I went to one of my carry loads... Federal 124gr +P HST JHP my guns started having issues. They went into battery very sluggish for the last 0.25" of travel. Striker released but no strike mark on rounds. Rounds did fire without issue when rechambered to test. Not sure if the JHP profile is hanging up going into battery or what (I am using factory recoil springs and the guns are both on the new side right now). Anyone have experiences with other bullet profiles besides FMJ (I did see the issues with 150gr Syntech which I had laying around as well and didn't take to range to test because of the other reports lol)?
  3. matt7184

    CHPWS Screws

    This doesn't surprise me. I haven't had good luck with the quality of their products and have used more of their plates than I can count on one hand. Sadly though, I think crappy screws are common in the industry.
  4. Fact of the matter is you are giving out bad information. The manufacturer of the plates has these dimensions and has tested this thoroughly. I have tested this. You have not apparently. FCD MOS plates are for Trijicon RMR footprints only (excluding Holosun) for a reason. When you get a Holosun and test it with a FCD MOS plate please let us know.
  5. Except it does work that way (Holosun does not hold as tight tolerances as Trijicon in manufacturing). I have personal experience with all of the items discussed. Most Holosun RDS with "RMR Footprint" will not work on the FCD plate. This has been well discussed on other forums as well and by the manufacturer.
  6. The footprint may be the same but certain plates are made to tighter dimensions. Don't be shocked if your Holosun won't work on a FCD plate that is made to tighter tolerances than a Holosun...
  7. I've had this same issue. Pull trigger to rear and use a set of needle nose plyers to turn the pretravel take up screw.
  8. The Legion one should fit.
  9. What was the weight on your legion trigger from the factory? I'm debating going to this trigger as I think I want a shorter LOP.
  10. https://www.smith-wesson.com/performance-center 5", 4.25" models and both with ported models available as well. The overtravel adjustment seems interesting.
  11. matt7184

    P320 X5 Thread

    I haven't noticed any issue from the notch on my Legion + DPP compared to my non Legion X5 + R1.
  12. I initially thought my Legion didn't lock up as tight as my pre-Legion X5, but I notice that Sig also seems to lube the Legions generously compared to the pre-Legion X5s from the samples I pulled. Looks like they are still using TW-25. When my Legion X5 was used a bit and the lube came off it seemed to be almost as tight as my pre-Legion X5...not sure it's any significantly different and if so probably done to lower the return to battery complaints when people ride the slide closed.
  13. I've found this to be the best technique. And yes OP some of them are tighter and annoying especially when new.
  14. matt7184

    Romeo 1 Pro

    Romeo 1 Pro is supposedly starting to ship next month.
  15. Have any of these "R2" cut guns made it to the market yet?
  16. matt7184

    ZEV OZ9

    Why would it be hard to believe that the DPP footprint used on the M17 would become the "gold standard"? I have heard the same about the Type 3 RMR and Sig also is moving to the same footprint. Just because they release a new version of the RMR doesn't mean they can't sell the same Type 2 with the "Classic RMR" footprint. Adapter plates can also be made if customers want (see the KE Arms RMR to ACRO Plate).
  17. Yup I've used them for my RMR equipped Glocks. I like how much tighter and cleaner looking the RMR mounted is with them
  18. https://www.thefirearmblog.com/blog/2019/03/07/interview-with-eric-grauffel-changes-brand-and-joins-the-cz-shooting-team/
  19. Max has made comments about a 320MAX in comments
  20. If you want bright try the newer 6MOA Romeo 1s...They make my Aimpoint Micros jealous...
  21. Have been using my X5 + R16MOA + GoGun Gas pedal in a Trex Ragnarok + X300 Holster without any issues
  22. This looks interesting to me. Are there any holster options (for competition or other uses)?
  23. matt7184

    Shadow 2 Undercut

    Is it me or is the trigger guard undercut area sharper on the Shadow 2 than the Shadow 1/SP-01?
  24. Yes I have two with that set up. No issues.
×
×
  • Create New...