dansedgli
-
Posts
1,276 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by dansedgli
-
-
How can the FCD which sizes the fat side of a 9mm case swage a bullet which fits into the skinny end?
It's tapered.
In 40 it might, but 9mm? Doubt.
-
load longer or sort your brass.
Some brass gets thicker than others as it tapers down which makes it unsuitable for heavy bullets. -
Bruce said it himself. All reloads are out of spec.
If the same reloads work in several guns but not a sig, its definitely the ammo.
These issues have been around for years on here, I posted in Feb 2019 about it. The p320 barrel is not supported enough to contain the same amount of pressure as barrels from other manufacturers.
You can load around it. In my case I had to sort brass by headstamp or switch to slower powders. PITA so I got rid of the 2 guns.
PPU, Tulammo, CBC were the worst for it. WIN would bulge a little bit.
-
If you are worried about using too much powder use heavier bullets.
I shoot 160s with 5.8 grains of wsf at 175pf.
-
Changing a magwell takes about 4 seconds.
Not sure why SVI doesnt show them separately on the website but you can option them on the grips. Maybe you'll need to contact them.
-
+1's should fit. They fit with my gun last time I checked.
Factory edge sights are fine. You will need to squish them down to get in the box. A standard Edge is made to fit perfectly with not much wiggle room.
That is the wrong magwell though. You need to swap it.
This is my standard gun. The cheely magwell scrapes in but it would fit much easier if the front of the magwell was bevelled like the SVI above. If you draw an imaginary line across the bottom of my basepad that is what needs to go. It really needs a push to get in a tight box as it sits.
-
Angled basepads on 124/126mm mags. If you have an infinity with low profile sights you can fit the plus 2 pads. If not you must use the plus 1's in this pic.
That's what I need with STI mags in my STI tactical with novaks. An edge with bomar sights has more room.
A standard division magwell has a taper on the front like the svi below.
-
I just use 357 sig dillon dies.
Mr Bulletfeeder 9mm flare die in the powder drop.
You should lube your brass anyway. I use hornady one shot.
Plot twist: I mainly use 40 cal brass because it is free. There are some sig cases in there but not many.
-
9 minutes ago, Dirty_J said:
Customer. Service.
They called me a liar once when I said my mate kept busting locking blocks.
He hasn't been able to shoot that gun for months now. Don't buy one if you don't live in the USA. Lesson learned I think.
-
I've had heaps of case failures due to no chamber support which is like being out of battery a bit. They never did that to a case head.
Double charge is my guess.
-
Decibulls are the ones you mould yourself right?
I think that's what mine are and they are great.
Easy to see why people have different opinions though, if they moulded them poorly.
-
45 minutes ago, terrydoc said:
Not had 1 case issue or any other issues with the X5 that Dan used to own.
You also hardly ever shoot.
-
Probably just a coincedence though.
-
4 hours ago, texasdawg said:
What do you think, Mr.Ssanders224, is this a 9 major, 9 minor, 2011, or a P320 case? With your broad view and with head firmly above the sand you should know what happened in my gun? I did not attack you personally first,,, I was making observations to the title of this thread,,,
Higher than normal pressure in a reloaded WIN case. Same as the cases my infinity would blow out when I shot 357 sig with a certain powder.
Here is my small collection of P320 shenannigans.
-
11 minutes ago, texasdawg said:
All the people that I know of who had a case rupture were using either remanufactured ammo or were using reloaded range brass. Never have I heard of someone using new ammo have a case rupture. I have had a case ruptured and it was with range brass reloaded. YMMV,,,
I also agree with that Jim fellow, the stock design of the P320 will not allow a P320 to go off by itsels,,,
How many times have you had case ruptures with other guns?
-
Like the chamber support issue, it just happens far too much to not be a problem with the design.
-
My X5's were the worst guns I've ever bought.
-
What the heck. Nice colours.
-
I used a 38 special sizing die and 9mm everything as stated above.
I don't know if I'd buy a 9mm if I had my time again. 38 short colt was pretty straight forward.
The only downside is 38 special brass around here is mainly winchester non + P for wadcutter ammo seated deep. These don't fit in my moonclips for starline brass.
-
They want to make 45's obsolete in classic division. Dumbest s#!t I've ever heard.
Appendix D3: Classic Division 19. Magazines accessible to a competitor during a COF must not contain more than
89 rounds (for Major power factor) or 10 rounds (for Minor power factor) at the Start Signal -
They break the indexing rings often.
A friend had one on a 650. Finally got fed up and upgraded to an 1100 with the mk 7 instead.
-
3 hours ago, Thomas H said:
Does anyone think that Nils would have shot it SLOWER with a Limited Major gun? I doubt it. Would his points have been better? Obviously, because that's what Major gives you.
100%
-
index slowdown is not bottom slowdown.
Look at the video. There is a different slider for it.
-
I didnt have that on my mk 7 pro 1050.
When did .357 SIG get approved for Limited Major?
in USPSA/IPSC Rules
Posted
It's easy to make out of 40 brass. That's all I shot for years and was free from the police using our ranges.