Jump to content
Brian Enos's Forums... Maku mozo!

kmca

Classifieds
  • Posts

    1,387
  • Joined

  • Last visited

Everything posted by kmca

  1. Just an FYI, ProEars is having a special today (sale ends midnight 1/3/16). $199 including free shipping for any of the Gold series muffs.
  2. The smiths I've checked with, new barrel and comp run just under $1000.
  3. why not? You'll save shipping costs with your other purchases Actually, they're all about the same..
  4. One of my alarms quit working, so, with Dillon's famous warranty, they sent me a new one. The new one has a much softer "beep". The old one was loud, the new one is just loud enough to let me know it''s time for a refill.
  5. UPDATE: After I drove the pin deeper, I had to take a Dremel with a cut-off wheel and very carefully cut about 1/8 inch off the pin, drove it doesn further, cut another 1/8th off and continued until it was all the way through. It took a while because I didn't want to nick the receiver. I cut a new pin so that it's flush with the bottom of the receiver. In the future, if I need to remove the latch again, I'll take a solid pin, about 1/8" long, slightly smaller than the hole, and drive the pin out the bottom far enough to grab it with vise grips. Anyway..thanks for all the help.
  6. No clip retainer. I don't have a #0 or #1 tap, I can't even find a screw small or long enough to fit into the hole
  7. It's a hollow pin on the side opposite the ejection port. You sure get up early or stay up late
  8. Ok, I found the problem and I was rather ignorant in my explanation. I went to my local Bass Pro store and looked at another Versamax. The left handed version (which is what I have and failed to mention) is NOT a mirror image of the right hand version. The hole in the right handed ejection port is clearly visible. Mine doesn't have one. So, the only thing I can do is drill out the pin. There is no through hole to drive the pin through. Any way...thanks all for your input
  9. Ok. I think I see the problem. If there is a hole in the rail, it's a blind hole. The pin looks like it an only be inserted from the bottom of the receiver.
  10. Do you mean there's a relief hole in the upper action rail? I used a roll pin punch and the pin seems to have bottomed out when the pin contacts the upper rail? It can't be that difficult???????
  11. Thank you. I guess I was having a "stupid moment". Did you happen to leave the inner latch spring out when you replaced the latch? My bolt release button is very hard to push. Ok, I tapped the pin until it touches the action rail and it doesn't release the latch???? It seems the pin might be too long?
  12. I've been looking at the receiver for a couple of days and I can't figure out how to get the shall latch out so I can tap it for an oversized release button and contour the latch so it's easier to load. Sorry if I'm a little "dense", can someone give me some advise?
  13. http://www.proears.com/Wednesday only though. I would need about 70% off to afford a pair of their custom plugs. Wish the price of electronic plugs would come down.They occasionally have a $500 off sale during the year, if you have patience. I wouldn't mind (too much) paying for those ear plugs, but I've tried in ear electronics before and was disappointed in the sound quality. And, the guarantees from most places don't cover custom fit plugs I'm gonna assume you didn't try the sport ear 360s or the Extremes? That would be correct
  14. http://www.proears.com/ Wednesday only though. I would need about 70% off to afford a pair of their custom plugs. Wish the price of electronic plugs would come down. They occasionally have a $500 off sale during the year, if you have patience. I wouldn't mind (too much) paying for those ear plugs, but I've tried in ear electronics before and was disappointed in the sound quality. And, the guarantees from most places don't cover custom fit plugs
  15. The most I've ever had to do was put some duct tape over the nut, use finger pressure against the nut, and use a power impact driver to back the screw out.
  16. Look at this thread: http://www.brianenos.com/forums/index.php?showtopic=222091
  17. Lower the volume. But it reacts and recovers so fast, it's almost like they turn off
  18. Who, may I ask, gets $400 + for that kind of work? (my kid's college fund can use that type of pricing) It's an quote I got from Americhoke. That was for shortening the barrel, rethreading it for the screw in chokes and removing the rib.
  19. Why? aesthetics mainly, it also keeps the carbon off the mag extension. Thanks, that's what I wanted to hear.
  20. Ideally, the barrel would be flush or a little shorter than the mag extension.
  21. I've got a 24 inch on one shotgun and I like it. I'm considering getting a particular backup gun, but the only one I can find has a 28 inch barrel and I can't find any shorter barrels. I plan on at least a 10 round exetension. My queston, is it worth the $400 or $500 to get it shortened and re-choked at 24 inches?
  22. He makes a run when he gets enough inquiries/orders. Got mine about 6 months ago.
  23. Depends on how handy you are. The best camera, for critiquing your technique, is one held by someone else.
  24. It works anywhere the 625 works. I have one cut for clips and load 44 Russian. Meh....those thin, fragile moonclips do not work as well as .45 ACP moons. I haven't really noticed any big difference between 44 and 45 clips. When someone steps on either, they both fold over
×
×
  • Create New...