Jump to content
Brian Enos's Forums... Maku mozo!


  • Posts

  • Joined

  • Last visited

Profile Information

  • Gender
  • Location
    Tucson, AZ
  • Interests
    turtle races
  • Real Name
    Tony Conesa

Recent Profile Visitors

1,184 profile views

pitvpr's Achievements

Finally read the FAQs

Finally read the FAQs (3/11)

  1. Yes, the "little" spring is in the striker assembly. Anyone know if this trigger bar will work on the SFx: (From APEX Gun Parts)
  2. I spoke with Freedomsmith about this, and they had the following response: “ordinarily this is a plug and play installation. Unless there have been some type of modifications or damage done during installation. Such as lighter weight springs that might preclude proper reset. Or bending of the action bar during installation (common when using the non removal of action components method, which is never recommended). I will seek other opinions and perhaps someone has heard of”
  3. The trigger resets, that's not the issue, the gun shoots. The issue is that the striker is not resetting when you rack the slide while holding down the trigger. The striker ONLY resets if the slide is racked WITHOUT holding the trigger.
  4. I just picked up a used Canik SFx a few weeks ago that has a re-set issue. The gun came with a Freedomsmith trigger installed. The issue is that the striker will not re-set when racking the slide as your holding the trigger down. The gun WILL re-set the striker “every time” when the slide is racked and the trigger is not being depressed. And, interestingly enough will re-set the striker while holding the trigger BUT ONLY if the slide is pulled back all the way to end of travel. However, it will not re-set the striker is the trigger is being held and the slide racked to less than 90% of it’s rearward travel. I though it might have been a spring issue so I did replace the existing springs with a new Galloway Precision Reduced Power spring kit, (blocker and trigger return). This is not resolve the issue. Anyone can give me a suggestion, would be appreciated.
  5. What spring is recommended with the W74 tungsten guide rod? I've heard 1911 Commander length is this correct?
  6. @zzt Yes I have read the HP disclaimer. In a nut shell, I am a big fan of HP triggers and prefer the Radian safety. I have two PCC's right now. both have HP riggers, one is an older 24ECL model and it works with the Radian safety, the newer HP "Hipertouch trigger is s slightly different design and will not work with the Radian safety, doesn't allow the trigger to function at all. I was just curious since I'm building a third gun and trying to hunt down a safety that I like as much as the Radian.
  7. The specs on this gun call out a Hyperfire Eclipse with a Radion Talon safety? Those don't work together, how is that?
  8. The specs on this gun call out a Hyperfire trigger with a Radion Talon safety? Those don't work together, how is that?
  9. Same here, it's all about what's hanging off the front of the upper that makes the diff.
  10. @TRUBL So your Delayed Blowback Recoil System is the speed demon of the bunch? The name is misleading...
  11. Agreed, I have the Brekke/Max 10.5" barrel comp system, and in corresponding with Max about optimizing the setup, he prefers the weight in the bolt and the added weight from Blitz. I'm running the Blitz buffer, and altogether my "tail heavy" setup is much softer and has less dot movement than most of the other blowback PCC I've tried.
  12. I also run the same bullet same powder 3.8gr and I too think they cycle faster, my Bill Drill splits come in around .12~.13 (4" groups). Just curious about the bolt weigh, why take it out?
  13. I been testing the MBX 2 Stage against the Blitzkrieg running 115g bullets at 130 pf. (MBX using the middle spring weight. The Blitz system using the weight). Just recording split times with zero points down on a standard bill drill, my splits were consistently better with the Blitz. I have not tried using the weight on the MBX system, that my next project...
  • Create New...