chipu12

plus one on the cobalt bits...but good quality ones not the $4 from Amazon, almost ruined my TS when snapped

what brand die you use for decapping? Had the same problem on a Lee/Egw under size i had to lower the decapping pin in the die.

plus one for the pyrex powder hopper, more consistent throws

...so what's a decent price for hard chroming a CZ?

so no backlash on the uniquetek powder measure? any other options budget friendly?

i know people that got more then one "pew pew" with a single trigger push around 30-35K so i changed mine at 25-30k just to be on the safe side, really crisp trigger with the new CZC hammer

why i'm thinking it will be well into the summer until realistic will see one for sale

not a slide bite but one of my "south paw" shooting buddy with an Sp01 was complaining about the protrusion of the slide stop digging in to his tight hand thumb

did you have to send the slide or just the bushing to CZC? thanks Chip

TSO in 40S&W, i bought four complete 140mm mags from CZC , a little bit pricey but i can use 21 rounds reliably in all four with no problems. One of my shooting buddies had two broken Taylor Freelance base pads on 40 mags after dropping them on the concrete floor a the range, no issues with the CZC on same floor.

really tight tolerances on the Uniquetek clamped tool head, i had to do the alignment procedure recommended by Dillon also tight the screws on the tool head with all 5 station filled and still have some crushed cases on station #1 if I'm cranking fast.

I would not recommended it,i had the exact same free play problem as described above, i used a piece of fine wire around the notch where the c-clip retainer goes on the threaded shaft to take out the free play, still not perfect but its ok for Uspsa loads. Chip

don't need it...but want one..or two...bad

nice to have items http://www.ebay.com/itm/Dillon-XL-650-SL900-Bearing-rotary-shell-plate-cam-follower-/222384485888?hash=item33c725f600:g:LpUAAOSw2xRYWc1c http://www.ebay.com/itm/Dillon-XL-650-and-SL-900-Performance-Improvements-kit-/221316500435?hash=item33877dcbd3:g:xNUAAOSwaA5WkuPn http://www.ebay.com/itm/Shellplate-Bearing-Kit-w-low-mass-detent-ball-for-Dillon-650-/191271651675?hash=item2c88adc95b:g:H-0AAOxyCbFTmJqs installed the above items and my 650 and now its smooth like silk, the only problem for the first two items is the really slow shipping(3 weeks) Chip

nice set up guys, maybe somebody can come up with some kind of optical sensor that can check for the powder level in the case...

I've tried to preorder one at a local Cabelas in IL and strange enough the claim they couldn't find it in their CZ catalog. I guess i'll peel my eyes online for one when they'll start trickle in the country

Accu Shadow ...147gr coated lead, 3.8gr Power Pistol, Winchester WSP primers, 1.120 OAL, around 128PF

I'm planning to buy the mount, I'll keep you guys posted about the result.

still on topic...that means i can install a C-More Cheely 90 degrees mount for the Czechmate on the TSO ? Thanks,Chip

TSO...180gr coated lead, 5.2 Power Pistol, 1.12 OAL, 168-170 PF ,pretty clean a little bit flashy.

On my Tactical Sport 40, 14lbs hammer spring did not ignite S&B primers reliably only after I've changed the firing pin with the extended one from CZC.

On my Sp01 Accu Shadow the "auto close" its happening if you slam the mag in but it never happened on my Tactical Sport, i think its because of a higher spring rate on the recoil spring also the slide stop seems to be stiffer on the TS.

any idea how expensive is to hard chrome a TS? Thanks Chip

is the install a easy diy job? special tools or procedure involved? Thank you

it's about supply and demand...hopefully CZ it will be different than Tanfoglio story that drove the prices into the sky$$$