Jump to content
Brian Enos's Forums... Maku mozo!

Unibrain

Classified
  • Posts

    105
  • Joined

  • Last visited

Profile Information

  • Gender
    Male
  • Location
    Portland, OR
  • Real Name
    Jim Boone

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

Unibrain's Achievements

Finally read the FAQs

Finally read the FAQs (3/11)

  1. That corncob stuck in the JHP can and does cause problems when it shakes loose in your gun. I know three different open shooters who swore by dry tumbling until they tracked issues to the corncob media. (Failure to feed and failure to go into battery) YMMV but what problem are you trying to solve by tumbling?
  2. Of all the places I looked I didn't look in the obvious. Thank you!
  3. With all of the special elections over the past 3 years, I’ve lost track of all the current terms and what positions are up next. I’ve scoured the USPSA website and am unable to find the current AD terms and when they are up for reelection. Does anyone have a pointer are can you refresh me?
  4. I've had my slide racker fall off and I couldn't find it on the ground. While I didn't do it intentionally it resulted in the same modification. So was this an allowed "modification"?
  5. Our club matches fill up in a day or two and are on waitlist for a several days before the match. We use the waitlist as more of a holding pen to help balance out squads. Everyone who registers gets in the match. Matches are in the 70+ and we've not had unusually long days. If/when we push 100 we may revisit the policy. As for giving a preference to USPSA members, that's an interesting idea but means more work for the registration dude, i.e. me.
  6. Correct. If you don't have a mag gauge(1) be sure to have chrono do a curtesy check. Some 320 factory mags and some extensions don't fit the gauge! (1) If you don't have one they are less than $30.
  7. Link is good for 7 days https://discord.gg/a9ztzG7S
  8. They are getting in the right bucket but barely. Every now and then one will get in the wrong bucket. For this version of the sorter slowing it down a touch solves the problem. There is a new version in development (CS7.1) that has a much shorter drop tube to correct that error, up date in the comparator to sense when brass has cleared, auto homing and a few more updates. https://github.com/sjseth/AI-Case-Sorter-CS7.1 There is an Discord setup with several active users doing the development.
  9. I have this https://github.com/sjseth/AI-Case-Sorter runnnig at a nice clip. I still need to do a bit of training on the system but with minimal training it’s sorting out about 80% of the brass with high accuracy. There is a new version in development that should be even quicker. Here is a quick video of the machine in operation
  10. Starting the printing process and have all the hardware. If all goes well I’ll have the first part running next week and be able to train the system.
  11. I sent in my Atlas Chaos v1 to AGW using this program. Shipping both directions is included. I tear my guns completely down a couple times a year and used this service at the end of the year. Given how much we spend on everything else (guns, ammo, travel etc) $300 for a once over, new springs, and returning the extractor and trigger was a no brainer for me.
  12. I've set all the button options to be the same (Pro-mode, 5 min, etc) so I don't accidentally turn it on in the wrong mode. I only use the camera for shooting so I don't need the other modes.
  13. There are a couple settings you need to change. There is a wind noise setting you need to change to not clip sound. I also highly recommend shooting Pro mode. Pro mode lets you reframe the video after you record. This adds a step in the editing process but is worth it.
  14. Looking through the results that are PractiScore there are some suspicious scores. How does IPSC handle those? For USPSA I'd call out rule 9.10.2 and it would be corrected if someone arbitrated. I'm looking at the Open scores for stage 16 with an impressive 60HF!
  15. And Appendix E says, "The primary magazine measuring device shall be the EGW mag gauge"
×
×
  • Create New...