tiger49931

I hear what your saying about the low ports being 6'6" the 10" off the ground ports seem s to be my downfall. Literally once down getting back up is a pain especially at 50 wasnt so bad at 30 but now i think i need yoga

gotta say Salomon all the way love all their shoes. but different models for different conditions

ty for all the info ill check those out

Any one ever have a problem with the trigger weight going from 2 lbs to almost 15 sometimes on their open gun? Just had the chamber reamed from 9mm major to 38sc But dont think that would effect the trigger. With out a magazine its like 2lb trigger with loaded mag and under the clock trigger is about 10 lbs and had to set off.

Anyone running 147's thru their X5's yet . they keep good accuracy with heavier or does the X5 like lighter rounds ? Just bought mine today after the link in my 2011 broke i figure imma need a backup gun. I was also wondering about POI shift switching from a red dot to the irons back to dot etc depending IDPA or USPSA production or carry optics.

so question for all the n320 guys what is the SD your getting across a load quantity of say 50 ? same top the CFE guys ?

i love the 147 ibejihead over 3.6 WST and a COAL of 1.135 out of a STI marauder = 133pf all day long or exact same set up with TG at 3.0 grains

ty for the heads up on that.

i HAVE A DILLON CV-2001 AND I USE WALNUT SHELL BUT AM STARTING TO GET A LOT of dust on the cases etc.. Any ideas on how to stop this ?

If you want the most accuracy out of your barrel you will need to ladder your loads and see what harmonic the barrel likes. Ive had great success with 3.6gr WST at 1.145 147gr flat point blue bullet. 4gr WST 1.10 125gr round nose Blue bullets and 3.0 grains of titegroup 1.145 147gr ibejeheads. The blue bullets didnt seem to like tite group in my gun anyway.

I'm using ibejiheads 147 and 3.6 wst at 1.135 coal and getting 133pf out of my sti marauder. Sent from my SAMSUNG-SM-G920A using Tapatalk

WST is the powder for me keeps groups tight out to 60 hit steel easy at 100.

ok the gun seems to like the 3.6 grains maybe i need to play with C.O.A.L. ill try shortening it to see what happens. its running 135 or so PF

I broke the barrel link on my marauder and sent it in they said i needed a longer one? so i had STI replace the link now my guns groups seem to have opened up at 25 yards with the load i was using. 3.6gr WST federal primers C.O.A.L. 1.15 Is this the link or just me? can the length of the length effect accuracy at a certain load? Do i need to re ladder my loads to get the best accuracy again?

sig p 320 seems like a good start also ?

Loading the blue bullet 147 for my M&P i found groupings didnt do well when using WST at 3.6gr but the 124 at 4.0 shot one hole at 50' talked to S&W there twist rate is not good for the really heavy 147. so i bought a storm lake barrel and they work pretty well now. but now i shoot the 147 in my marauder and my steel master and they love them.

Talked to sti they said they are going to fix and only needed the barrel? Sounds weird to me that if the link broke because inproper barrel fir then maybe you might want the slide with it? but any way sent the barrel to them today. so it went second day air they will have it on wednesday and return time will be ? lets wait and see

maybe about 2-3000 rounds IDPA 130k PF stuff so light for sure . They are definately getting a call tomorrow i know they will fix it. atleast i hope i will be sending back all parts

So im on almost my last stage at a local IDPA match when my STI Marauder goes from a frantic semi auto to a single shot. I finish the stage ( only had 1 target left) Then i return to the safety area to tear it down and see whats up. Thinking since it has never had a problem before and i didnt clean in after my last practice maybe she is getting finicky and needs to be cleaned. So i break it down and out drops a half circle piece of steel that i was like OK where the heck did this come from low and behold its the lower half of the circle on the barrel link. So my question is 1. Does this show a greater problem Barrel not properly fit , Slide fit incorrect etc . 2. is this a normal piece to break if so will STI fix it or should i send it out to a different gunsmith? As i have several STI's and 1911 and have never seen this happen before i am a little apprehensive about what could be going on with my pistol.

i like this topic because when at a match after the buzzer goes off and after the second shot all i hear in my head is " Vogels already done .... " keeps me going to try to be faster

what power factor are you running I run a 147grain 9mm at 137 PF with a 11lb springer recoil spring . had a 9LB but on bill drills my spread averaged 10 inch or just a hair more went to a 12 now the average is about 5-6 inches 10 shot from the holster at 10 yards.

So here is the question i just finished my 5K= rounds of 147grain RNFL lube ring and looking to order more and now my supplier offers a 147grain rn without a lube ring or my regular bullet with a lube ring. Im always looking to squeeze a little extra accuraccy out of my pistol so my question is, Has anyone shot both lube ring and non lube ring and noticed a difference in accuracy ? One would think the extra bearing surface would help the bullet spin and there for keep its trajectory true longer ? Or is it just a flash in the pan easier to load into the casing thing? Of course these are poly bullets ......

To try to save the division i woul dlove to see or get the numbers on how many people quit or changed divisions when the rule went from 5" to 4" for revolvers. Maybe they should bring the 5 inch rule back to try to save the revo division alot of 5" revolver shooters in uspsa looking for a place to shoot their 6 shot 5" revolvers? Just an idea. I dont shoot esr mainly but i have qualified in it. Make a stand alone event for revolvers that wayt people who shoot in both catagories ( semi and revo) dont have to choose at a state match what you want to shoot the semi you have been really practicing with or the revo you take out evcery once and a while..

Trying to find load data fir 38 special and 160 gr bbi using clays or WST i have 32 pounds of each. any help would be greatly appreciated. looking for high low and OAL.

I love them been using them for the whole season was able to shoot a side bet thing at a local club match hit a half size steel at 131 yards 9mm 147 gr . Do a ladder for your pistol and you will find they are really accurate.