-
Posts
156 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Everything posted by works for ammo
-
TSO and 40 ammo problems
works for ammo replied to looking4reloadingdeals's topic in 10mm/40 Caliber
Yes it may help. Or ever try a mr bullet feeder powder funnel to bell the brass. -
TSO and 40 ammo problems
works for ammo replied to looking4reloadingdeals's topic in 10mm/40 Caliber
Since you are using the undersizing die, the i.d. of the case is being sized down .001 more than usual. The bullets you are using are coated so they vary more than jacketed and some are probably .401 dia. If you aren't belling the case mouth enough the bullet may seat crooked in the case. That's why the marks on the case with the sharpie on it are opposite of each other. I have this issue also when loading coated bullets with my 2011. I will get about 10 rejects out of 100. Now if I load Jacketed bullets or even plated, only about 3 or so fail the chamber test. All of them that fail work fine in my Glock G35 so I load at 1.135 These are some of the issues I have ran into while loading 40 -
I have the Redeye tactical one that SJC sells. I have not shot this in a match as I've been shooting CO with a gen 5 G17. When I had the gen 1 weight I used the WSM 2 holster from CR speed. The Toni weight looks good too
-
They have a second version out now that sits back a bit further on the frame so it fits flush with the G17 slide. It doesn't use the aluminum plate and set screws to secure it. Now it is 3 pieces. I like the new design better. He it is on my G35 w/9mm conversion barrel.
-
I chose a ZEV duty slide for my gen 5 g17. It has front and rear serrations too for around $280 Its milled low for an RMR. I have also had dovetail mounted red dots on various pistols and that works fine too.
-
Contact ETS or magpul and see if they have any interest in making plastic mags for the 2011.
-
Any USPSA near St. George, Utah 10-12 to 10-16?
works for ammo replied to OPENB's topic in Travel, Locations, Ranges, etc.
Hello. It looks like there is a UPL match @ pro gun club outside of Vegas that weekend. Shoot Sat or Sun. time plus penalties. http://silverstatepractical.com/calendar/ -
Usually after I pull the trigger once and realize the safety is still on. Just kidding, I disengage the safety when support hand meets the grip and I'm extending the gun. This could be done a bit later in my draw but i dont think it would hurt or help any time gains.
-
My g34 load would be 135gn coated bullet with 3.7 of WST at 1.125 oal Still using the stock recoil spring assembly though
-
Nice pistol. If I were shooting that gun I would change the front sight to a narrow blade like a .100 or .90, Add a magwell, extended mag catch drilled and tapped. Would get some 140mm mags too. Or just shoot the crap out of it the way It is.
-
CZ Custom Shop dove tail Optics mount anyone try this yet?
works for ammo replied to kmanick's topic in CZ
I haven't tried it yet but I ordered the Henning mount for a deltapoint pro to try on my S2. Open minor here I come, as I think it will be hard to make weight without any milling with this set up. -
I have a pro match 40 and no mods were needed to run STI mags (gen 1) Using grams spring and follower w/tti base pads. Getting 20 rounds
-
My pro match works with sti mags no problem. Extractor tension was a bit too much from factory and the last round wouldn't push up under the extractor. Once I took some tension off the extractor it feeds the last round perfectly now.
-
-
I'm was going to post this question earlier. Hope you don't mind if I post a pic of my primers in your thread. I'm using a moly 125gr 9mm with 3.3 grains of clays out of a 5" 1911 . Are these signs of over pressure? Haven't cronoed aNY rounds but I think I'm close to max charge. 9 minor.
-
-
Las vegas matches April 18-may8
works for ammo replied to vixty's topic in Travel, Locations, Ranges, etc.
Looks like their is a match in mesquite, NV On Sun. 4-17 but I don't see anything going on in Vegas as Multigun nationals is at Desert Sportsman. Check out mesquite mayhem shooters on Facebook it's like an hour away. https://m.facebook.com/groups/1642115266027599?notif_t=group_activity¬if_id=1460558162400949&ref=m_notif -
Ok I just post a wtb in the classifieds. Thanks
-
Hi I have a gen 3 G35 with the SJC frame weight and was wondering what Holster to choose between the CR speed wsm or the Ghost "the one" What one is going to be the easiest to modify to work with the frame weight? Thanks
-
What holster for Limited Glock with SJC frame weight?
works for ammo replied to pbosik's topic in Gear & Accessories
Has anyone used the ghost "the one" holster with the SJC frame weight yet? -
Kinda odd Nevadashooters.com has been down all day too. Oh yeah and welcome.
-
If your shooting plated bullets and the crimp cuts through the plating You will see this.
-
One Thing I've Seen Every Match So Far
works for ammo replied to GunBugBit's topic in Miscellaneous BEginners
And whoever has the least amount usually ends up winning. -
http://www.brianenos.com/forums/index.php?showtopic=198991 I remember reading about this before.
-
Welcome!