Norone

UPDATE- There was some, a little, not much at all, set back on the FMJ. Not the Blues. Also, I have never cleaned the barrel. My CED always has first round low fps. So I looked further and boom there it was- the brass wasn't all the same as the vendor I bought from said it was. So everything y'all said was a contribution. Gonna get a LAB or Garmin soon too. Hey FARMER- Black magic marker? You mean the crimp station? Thank you all.

CED IR. 60 degrees. Light front wind. 147gr JHP, 1.16, same brass/primer/bullet, 2011 bull KKM and never cleaned barrel. 821, 834, 844, 858, 863, 877, 886.......? Upwards? My first shot on the chrono for years is always the slowest but this was odd. Wasn't set back. I check that. Doesn't even hit the ramp with a nose anyways. Here's an even odd'r part: 147gr RN, Blues, 1.17, samsies.... 910, 908, 914 - SD of 6? Any insights would be helpful!

I have finally like and proved a load myself... I think... Apollo Arms "lets try something out/prototype" 2011- 147gr JHP, 1.155-75 OAL, 3.51-2gr N320: SD was only 6 at last chrono and the zero was a stoplight at 15Y. 130PF.

Y'all- 9mm used for maybe 500 rounds, not abused. Had some 1.155OAL 147gr JHP nose dive on my 2011. Right at the base of the ramp. Only like 2, 3 times at a level 2 last week. Y'all have any ideas? Suggestions?

Im looking at 3.4 even with Everglades JHP @1.155 tops, to get me constantly over minor PF. All my Glocks are liking them too. But, I am gonna test hotter to see if it likes it.

Bring it on HOG. Thank you.

Coming off Limited had to start over. 5" build that was my upper and enhanced and built buy Kevin Chen at Apollo Arms. 147gr. Everglades JHP, 1.152 - 1.1.159, any primer, once fired brass mix, N320. 9lb spring with 4 coils cut off. 3.18gr - High of 808fps 3.28gr - High of 818fps (Glock 17 and 34 loved these) 3.35-39gr - High of 851fps For fun had some 147gr Blues TC at 1.152 with 3.28gr @ 863. Hotter returned faster, duhhhhh.... But man those blues were soft as heck. Looks like 3.4 minimum for JHP and the above for blues. Anybody have any recipes or load charts they did from scratch for 9mm LO 2011? Thanks!

That does help. Basically one 'damages' it if you take it apart. Windage gets limited in turns. Would have to guess at presetting it. Oh well. Thanks y'all.

I want to attach a TTI blade but can't figure out how to use the windage screw to remove the old and re-install the new. No YouTube vids either. Help?

Not to hi-jack, but who here loads 9mm minor as long as their mag will let them? I do 1.15 for Glock mags but all else I do longer. Anyone else?

G34- 1.15, 3.4 N320, 147 blue .355 2011- 1.16, 3.6 N320, 147 blue .355 Both are doing me great with the reduced slide weight(s) and 10-11lb spring. Though the Glock is 'pickier' on lock up. @130pf.

Thanks man., Lab Radar just ordered.

1.16 minor 3.2gr N320 on a 147 blue. Barely at 127pf. He said if he re-seats them lower to 1.14-1.15, it will get a higher pf. I said yes and no - It will come up 'some' but chamber pressures will be higher and initial recoil will be big snap. You guys thoughts??

Wanna dryfire while on a trip to SFO and wanted to know the do's and dont's. Is it just no hicap mags? Thanks!!

Thanks.

Y'all, Got a 22" 6.8 SPC upper free helping a buddy and was hoping you guys could help me make it into something. I would even consider boring out the chamber for a new caliber... Thoughts Ideas..? Thanks.

#2... sorted out! Geeked out while snowed in, at the dining room table and the wife just LOVED it! For the curious... Gen 4 ragged out lower, Adams Arms Optic ready 17 slide, The guts: Zev plunger/striker, Gen 5 disconnector (black one).

Late to the party but fighting with 2 that reset for crap for since Timney had these to buy. Watched 3 go down at a match in NC on my squad alone buy the end of 7 stages. Got Frankenstein on #1 and 'made' it work. Epoxy Dremel Jameson etc.... Runs good. Even had a spring company make incremental weight 'V' return springs. But the gauge is a bit more and had to take the slide release out til I could 'fit' it. Done. Solid now. #2, still working on it.

Im wide open to anyones insights into my new build. Commander length slide, .40 KKM threaded barrel, Sight block. More to the point, what lessons were learned and what pitfalls to be wary of as I can not find anyone to build this for me so I am studying up and allocating for tools. Thanks in advance yall!

Thanks yall. I thought no but wanted to hear from others.

All, I have had two very knowledgable MDs give opposing answers this evening so its to you all. - In Limited, can the butt of the gun, in holster, be below the the top of your belt legally.

They are around the same price but are there any real pros and cons to them when compared?

I ask as I would like some guidance as to m are the gun recoil differently. Anyone have any ideas? Thanks in advance.

Heard it was a Faux paaaaaaa...... but its seems no different.

Im not sure what you guys came up with but it was ok. Worked up a load. Anyone have crazy issues doing this?