Jump to content
Brian Enos's Forums... Maku mozo!

ffgats

Classifieds
  • Posts

    503
  • Joined

  • Last visited

Posts posted by ffgats

  1. Hi

    I have both the Gen2 SCS for AR15 223 rifle and GMR15 9mm PCC , are both using the same spring , meaning can I purchase the 5 pak and use it either the 9mm and 223? I want to use at least 10-15% lighter to both my 223 and 9mm. Need some clarification and advise on this, btw can anybody point the spring weight from factory to both 223 and 9. Thanks 

    did email JP but haven’t heard for a week now

  2. Instead of creating another thread might as well ask it here. I find the trigger not bad, but I prefer the Geissele SD-E of my 223. Wondering if it’s compatible with the GMR15. ( ask JP but haven’t got an answer, been a week already) Btw the 10 rounds and the 17 pinned to 10 is a challenge to load on close bolt, not sure if it will improve after some use.

  3. Yeah, was about to edit my post, my load right now is 3.8gr of N320 and 124 Frontier RN, oal 1.140, at first I replaced the factory recoil spring15lbs  to 10 lbs hoping to cure the problem. But this load work perfectly with my older Shadow2 non OR

  4. Occasionally im getting this failure to feed, (nose up) ammo, a couple of questions, could it be the extractor - too loose or tight, feed ramp needs polishing  or mags (lips and spring ) basically bnib gun less than 300 rnds, this happen 2-3 times per 100 rnds, haven’t mark which mag is doing it,  give your thoughts , thanks

  5. 12 hours ago, Snausages32 said:

    There's a spring kit you can buy.  The stock spring is the 85%, the kit comes with an 80, 90, 95, and 100 i believe.  I put the 80 on because I have an adjustable gas lock and light weight carrier.  You don't need it, the stock one is just fine.

    My castle nut is badly staked so its hard to take it out, will Dremel do the trick? Grind the pin, lol

     

    thanks, i just want to buy the stock( std) weight, no need for the kit, can’t buy direct from JP since they don’t ship to Canada, want to try the standard and the 80% too.

  6. just a follow up , I can't seem to find info regarding the main spring of the SCS,  are there any after market springs I can use, like the present set up of my SCS ( standard spring used). tried contacting JP, so far no response, my concern is where in the future to get replacement spring, Oring and bumper. I'm in Canada so Jp might not ship,

    btw, how often do you replace the spring. thanks

  7. Thanks, just pull the the trigger on the Odin 16” Intermediate , was able to get the last piece, and its only 30 mins drive. The next shipment is 6 months. Its a not light barrel, just a couple of ounces than my SPR

  8. On 12/22/2018 at 2:02 PM, yosturm said:

     I just got an 16” intermediate length  from Odin.

     

    Care to share your experience, accuracy wise and recoil, have you tried the rifle gas to compare, justfound a dealer with very limited stock. Thanks 

  9. 2 minutes ago, ffgats said:

    because nobody sells here 16' intermediate .

     my 18" ( rainier Ultra Match fluted) with rifle gas and adjustable gas block shoots the way I wanted, with 18" bbl 35oz, its a little front heavy, so I'm asking about the 16", unfortunately cant't seem to find a dealer who sells the 16' intermediate, just the middy. . base from your experience the 16" middy will not shoot like my 18' rifle. I thought the adjustable gas block with do the trick. good to know, thanks

  10. 9 hours ago, TonytheTiger said:

    No. You may feel it but you'll probably have a hard time noticing it in your stage times.

     

    The real question is why use a 16" mid when 16" intermediate and rifle barrels are available?

    Intermediate closes the gap on rifle so close you have a hard time telling the difference.

    16" rifle gas is not for everyone but if you like tinkering and tuning it can be a viable route.

    because nobody sells here 16' intermediate .

  11. Lets say everything is the same except for the bbl lenght 18” with rifle gas and 16” middy and both running Adjustable Gas Block, can I make the 16” shoot like the 18”, recoil impulse, softness and muzzle stability. Btw the 18” will be s little heavier. Thanks 

  12. mine doesn't run with 1145 fps even with reduce recoil spring. , the challenger 7.5, 3 drams 1 1/8 is good same with the AA 7.5  3 1/4 drams .  having problems with S@B slugs too, not too bad with Federal trubul mild recoil, but still occasionnally won't eject. the Remington mild recoil buckshot 8 pellets is not also 100%, full power Remi buckshot is ok.

  13. thanks for all your feed backs, nice to hear your actual experiences, yeah sometimes the price is little tempting, although I'm very happy with my Rainier UltraMatch Fluted 18" rifle gas,  I wish its around 28-30 ounces, its on the 36oz right now and I'm not a big guy. for Prone or Bench, the gun barely moves, its on off hand shooting that my arms can feel the forward weight.

     

×
×
  • Create New...