Jump to content
Brian Enos's Forums... Maku mozo!

ffgats

Classifieds
  • Content Count

    481
  • Joined

  • Last visited

Everything posted by ffgats

  1. BiggMike do you mind sharing your N320 load for your GMR15, I did try 3.8 and it was a soft shooting load but the accuracy was not satisfactory, then bump my load to 4.1 gr and accuracy is now great. btw I'm using Frontier Match 124 gr. 1.125" OAL, thanks
  2. So i can use one of the springs thats comes with the (5pak) for my PCC? Say the 100or 95%, thinking of using the 90-85% for the 223, running adjustable GB on my 223.
  3. Thanks, somebody mentioned not on BE that the 9mm use their 308 spring?
  4. Hi I have both the Gen2 SCS for AR15 223 rifle and GMR15 9mm PCC , are both using the same spring , meaning can I purchase the 5 pak and use it either the 9mm and 223? I want to use at least 10-15% lighter to both my 223 and 9mm. Need some clarification and advise on this, btw can anybody point the spring weight from factory to both 223 and 9. Thanks did email JP but haven’t heard for a week now
  5. Instead of creating another thread might as well ask it here. I find the trigger not bad, but I prefer the Geissele SD-E of my 223. Wondering if it’s compatible with the GMR15. ( ask JP but haven’t got an answer, been a week already) Btw the 10 rounds and the 17 pinned to 10 is a challenge to load on close bolt, not sure if it will improve after some use.
  6. tthanks gents, just ordered the hi-cap pinned to 10 today, and the factory 10 rounders is a struggle to load on the gun when bolt closed, not sure if I can cut a coil or 2 of the spring.
  7. and by the way, did anyone break in the bbl? as per the manual? thanks
  8. Just received my GMR15 and while reading the manual it states that the 10rounder is not recommended because of the design of the follower, I didn’t realized that the high cap( prohibited here up north) doesn’t share the same follower? Thanks
  9. ffgats

    Bullet nose up- S2 OR

    Yeah, was about to edit my post, my load right now is 3.8gr of N320 and 124 Frontier RN, oal 1.140, at first I replaced the factory recoil spring15lbs to 10 lbs hoping to cure the problem. But this load work perfectly with my older Shadow2 non OR
  10. ffgats

    Bullet nose up- S2 OR

    Occasionally im getting this failure to feed, (nose up) ammo, a couple of questions, could it be the extractor - too loose or tight, feed ramp needs polishing or mags (lips and spring ) basically bnib gun less than 300 rnds, this happen 2-3 times per 100 rnds, haven’t mark which mag is doing it, give your thoughts , thanks
  11. I have the GLS and it wont fit the S2, Glock, Beretta 1911/2011 does fit, ssme with S1
  12. ffgats

    Jp SCS2

    My castle nut is badly staked so its hard to take it out, will Dremel do the trick? Grind the pin, lol thanks, i just want to buy the stock( std) weight, no need for the kit, can’t buy direct from JP since they don’t ship to Canada, want to try the standard and the 80% too.
  13. ffgats

    Jp SCS2

    just a follow up , I can't seem to find info regarding the main spring of the SCS, are there any after market springs I can use, like the present set up of my SCS ( standard spring used). tried contacting JP, so far no response, my concern is where in the future to get replacement spring, Oring and bumper. I'm in Canada so Jp might not ship, btw, how often do you replace the spring. thanks
  14. ffgats

    Jp SCS2

    My castle nut is badly staked so its hard to take it out, will Dremel do the trick? Grind the pin, lol
  15. ffgats

    Jp SCS2

    Hi do you run the SCS2 without the buffer retainer pin, a little bit of pain to install and reinstall. thanks
  16. Thanks, just pull the the trigger on the Odin 16” Intermediate , was able to get the last piece, and its only 30 mins drive. The next shipment is 6 months. Its a not light barrel, just a couple of ounces than my SPR
  17. Care to share your experience, accuracy wise and recoil, have you tried the rifle gas to compare, justfound a dealer with very limited stock. Thanks
  18. From where, all I see here are 18” rifle and mid and 16” middy, interested on 16” intermediate.
  19. my 18" ( rainier Ultra Match fluted) with rifle gas and adjustable gas block shoots the way I wanted, with 18" bbl 35oz, its a little front heavy, so I'm asking about the 16", unfortunately cant't seem to find a dealer who sells the 16' intermediate, just the middy. . base from your experience the 16" middy will not shoot like my 18' rifle. I thought the adjustable gas block with do the trick. good to know, thanks
  20. because nobody sells here 16' intermediate .
  21. Lets say everything is the same except for the bbl lenght 18” with rifle gas and 16” middy and both running Adjustable Gas Block, can I make the 16” shoot like the 18”, recoil impulse, softness and muzzle stability. Btw the 18” will be s little heavier. Thanks
  22. any pictures of your rifles please, thanks
  23. Thanks for the info, that’s what I thought, proprietary ambi parts,
×
×
  • Create New...