Jump to content
Brian Enos's Forums... Maku mozo!

triggerhound

Classified
  • Posts

    66
  • Joined

  • Last visited

About triggerhound

  • Birthday 06/07/1971

Profile Information

  • Gender
    Male
  • Location
    Castle Rock, CO
  • Interests
    Shooting, Archery, Hunting, Camping, Motorbikes
  • Real Name
    Colin Shreffler

Contact Methods

  • Skype
    cshreffler

triggerhound's Achievements

Looks for Match

Looks for Match (2/11)

  1. Selling Quad Loads for anyone interested: http://www.brianenos.com/forums/index.php?showtopic=178112&hl=
  2. For those that might want to get their hands on one of these shotguns, please consider the following: http://www.brianenos.com/forums/index.php?showtopic=178074.
  3. This was actually the lowest load on the spectrum. This was caused by the bullet being pushed back into the case mouth.
  4. I found a few of them on Brownell's site. Seem pretty good and fairly priced. Thanks for all the advice!
  5. The rod/brush method of extraction worked perfectly. Thanks for the advice. Here are a few pictures of the brass with signs of over pressure, etc. I've run all my loads through the crimp die so I'm hoping that will solve my issue. I'll give another report after I'm able to test those at the range.
  6. Here is another shot of the primer with clear signs of over pressure
  7. The 45 cal brush/rod method worked perfectly. It worked so well actually I was a little disappointed I didn't have to work a little harder at it! Thank you for the advice. I'm super happy that's taken care of. Here's a picture of the case after both pieces were recovered:
  8. Well I have to first say that I really do appreciate the advice. I was almost afraid that I'd feel like an idiot after reading replies about all the mistakes I'd made. So thanks for taking my inquire seriously. The brass that I used wasn't once fired military as far as I know. I believe it was all Winchester. Dan, IMR 4895 and IMR 8208 XBR are extremely similar powders in burn rate, appearance, smell, etc. One of my friends thinks they are the same but marketed differently I'm going to try the cleaning rod/brush method of extracting the case first. I'll let you all know how that turns out. I'm also going to put all my ladder loads through the press one more time and add a crimp to see if I can avoid this SNAFU next time at the range. It sure did bring my range day to an abrupt end.
  9. Thanks Adam. So with the M1A I can't do that because the receiver blocks me from doing that at the breach end... I supposed I could insert the cleaning rod from the muzzle end and attach the brush in the receiver area... then pull it into the chamber and try to push it back out... would that work? I'm assuming that the friction from the brass brush will grab it and pull it out?
  10. I had a case split today while shooting reloads from my M1A. The bottom quarter of the case was extracted, but the rest of the case is snugly stuck in the chamber. Does this require a professional gun smith to remove or can this be done myself? Thanks!
  11. I took my M1A out to the range today to shoot some ladder loads I've worked up for competition shooting. I'm using IMR 808 XBR powder and 150 grain Hornady FMJBT bullets. I started out shooting some Winchester White 147 grain factory ammunition to warm up the barrel and put scope on paper. These shot perfectly fine and I was able to shoot about 20 rounds and easily get sub moa accuracy. The rifle shot great and felt great. I then moved to my reloads. I started with 5 rounds in my magazine. This first group of 5 were for 40.0 grains of IMR 8208 XBR powder. I'm not precisely sure the exact order of malfunctions but I believe this was the sequence of events: 1. Fired first round. Hit on paper. No issues. 2. Fired second round. Hit on paper about 1" from first hit. Double feed. I noticed that the rife was not in battery and fixed the double feed. While doing this I noticed that the bullet being fed from the magazine had been slightly compressed into the case mouth from the brute force of the Double Feed (I prepared these reloads a while ago and I'm not absolutely certain if I did a crimp on the case mouth). I'd say about 1/16" to 1/8" deeper. In hind sight I should have ejected this round, but I didn't. I know... 3. Fired third round into Berm to 'discard' it. Yes, I know I should have ejected it. That being said I didn't... What I found was that when I shot this third round the case split/broke. The bottom portion of the case was ejected and the remainder of the case is now stuck snugly inside my M1A chamber. So I have a few questions: 1. How do I get the stuck case out? Gunsmith? Or is there a way to do this myself? 2. Has anyone else experienced this kind of over pressure from such a seemingly small change in COAL? The case was completely split radially and the primer showed signs of over pressure also (flat and squashed). 3. I also noticed that on one of the cases from the first two rounds, the primer showed signs of being pushed out the back of the case, maybe half way out. Is this from under pressure or over pressure? In hindsight, I suppose it really wasn't that small of a change in COAL. I should have ejected the round and dismantled it at home. Any observations, experiences, advice would be very helpful. I have just never had this happen before in the 3 years that I've been reloading and shooting. This was the minimum powder load for this powder and bullet weight combination. I've not shot this rifle that much and this is the first time I'm reloading for the M1A. I've heard this rifle is a little finicky about ammo and gas pressure, but this is all very strange.
  12. Personally, I find it easier to shoot at the closer targets first, because sight picture is easier at closer distances. Larger targets are inherently easier to hit
  13. Also, Dan, would you recommend the aluminum or the steel version of that mount?
×
×
  • Create New...