gobabygo

I went from a 550, then added a 650, then added a 1050. After the 1050 I couldn't stand loading on the 550 & 650 so I sold them and bought conversions for the 1050 to do everything.

Went to the range with the Dawson's set and you're right. Impact was 3" low at 15yards with my production load.

Oh no. I literally just installed the recommended Dawson sights last night. Gotta go shoot it still but as you mentioned they have the "Perfect Impact" policy thing where they'll send you a new front sight if it's not zero'd. But you have to buy the recommended front or the sight set. If you buy a different front and you're wrong then I assume that means they don't have to honor the policy. Gotta say I do like the look of the rear sight on the gun (doesn't hang over the back much) and I like the sight picture with the .135" notch, .100" front. Just looks "right" to me.

Oh no! Just got my SP-01 and the photobucket pics are all messed up. Stupid photobucket looks to have changed something. Does anyone have a... copy or something of the pics in this thread? I read through this thread before I got my gun but now need to figure out how to clean up the trigger. Thanks.

I've been using the same Vibraprime for the last 15 years. Can't imagine spending so much for the RF100 or PAL. I like taking a break, going inside and loading up 10 primer tubes while sitting on the couch or in front of the computer. The kids used to do it when they were younger too. I don't think I ever get flipped primers since I watch them go down, but even if I did, how many would it take to make up the cost difference?

Right now the Deltapoint is my favorite optic... but I'm constantly looking for the next best new thing. Any one have both and can compare them? Thanks.

I'm a 36 waist and have both 38 and 40 CR speed belts. The 40 overlaps so much that when I run production and have mag pouches going to my back it can get in the way. Not sure what smaller waist-ed people do. With the velcro keeper thingy I bet you really only need a couple inches of overlap.

Also check to see if your ejector rod hasn't unscrewed and backed out so it's contacting the barrel underlug cutout place where it goes. Obviously I'm not a revolver expert... just happened to see this happen to someone (Itchy)... at IRC... at the end of the long field course.

In my 627 in 38 super I use 3.3gr of N320 and a Berry's 158gr .357 with an extremely heavy crimp to get to 125 pf. OAL is the standard 1.23". I have to crimp it heavy or else the bullets start walking on me. No idea on major since I only shoot ICORE. Oh, and it's an open gun so I have some holes drilled in the barrel. Burns very clean for me.

I have the Konus Konuspot-80 (20-60x80mm) also and it is excellent. I got mine a few years ago and at that time it was the best thing until you get to the Kowa for ~$800 if you want something appreciably better. I haven't been spotting scope shopping since then but I don't know if there's anything better for under $400.

The factory Ruger 10 round rotary mag seems to be the consensus for the most dependable 10/22 mag. Obviously you're limited to 10 rounds. I like the clear ones so you can see how many you have in there.

Had that happen to me at an indoor range a long time ago. A case took a bad bounce off the wall and dropped right between my glasses and my eye and left the exact same burn mark. I always wear hats while shooting now.

I wear Sordins and have always have them on. My muffs attenuate and don't cut off so I can hear the difference between a regular shot and a squid and I've never responded to the wrong timer. The only negative for me are the stunned gasps from the crowd when I screw something up, but most of the time you already knew it. However, earlier this year I heard the crowd gasp thinking I screwed something up (when I was behind a wall) that I didn't but I started laughing because of it. At least I got a laugh out of it.

CED 7000 for me due to it's size. When practicing I clip it to my belt and it doesn't get in the way while still recording everything. It has all the functions I'm ever going to use and more.

Interesting. The website has 3 CR Speed belts. The Hi-Torque, Super Hi-Torque, and Super Hi-Torque Deluxe. I think the only difference between the new Super and Super Deluxe are the stripes on the front. Anyone know if any of anyone with the new Super belt in the US? I'd rather pay a US distributor and not risk the potential hassles of shipping all the way from South Africa.