Jump to content
Brian Enos's Forums... Maku mozo!

prc77

Classified
  • Posts

    97
  • Joined

  • Last visited

Everything posted by prc77

  1. To start 33round with a + 12 Taylor Freelance ext. on the belt Standard cap with TTI base pad
  2. CDMGEAR has a NEW safety selector switch " Delta Wave" for the 500/590/590A1/930 series. Just a little something that might save you a little time at the BEEP. and possibly 30 seconds at the dump barrel. www.CDMGEAR.com
  3. thank you.. my luck, closed today Holiday
  4. I have a 5 year FN SLP MK1 bought it new and has had about 8000 rounds through it. Cleaning it today for a match next weekend. Reinstalling the slide and bolt and a part drops out. Seems the pin that hold the bolt slide and bolt slide link, broke. The remaining half stayed in place. The link is working properly, with the broken piece installed, under hand cycling. My ?, is that pin available as a replacement part, or is it new bolt slide time.
  5. Welcome to the fold young gun. I just want to be there when you beat your dad for the first time. Hope to see you at the NorCal matches.
  6. The Gen 4 Glock's small backstrap is intergrated into the frame, so yes, Production Legal . The M&P to be "legal" for Production, has to have 1 of the 3 backstraps installed.
  7. My Fat 50 Trooper Can: 300 rifle, 500+ pistol and 200 12ga
  8. OK now that I have the parts properly identified. I talked to Ben at JP this morning. He suggested a little heat to loosen the thread lock. I'm going to replace the set screw also.
  9. New build with JP Adust. Gas Block. JP LM BCG, JP LM buffer and spring. Winchester whitebox .223. Did not cycle. Gas Block will NOT adjust, open or close, will not turn at all.
  10. 1000's of RIO 3dram 1 1/8oz. 7.5's through my 3 year old SLP. Pistons sealed this past summer and it eats up everything.
  11. In the process as I type. Saved some money here and there, but went "ALL IN" on a JP Low Mass complete BCG and buffer, from CPWSA Picked up Shooters Source last in stock Nordic 18" barrel, saved 20%. Lower is a billet Quentin Defense, upper in a QD billet slick side, Comp is a Miculek (freebie). AP Customs 15" hand guard off the other rifle.
  12. Check out inlinefabrication.com for safe lights. IR sensor, + an 8 D cell battery pack or a plug in the wall variation
  13. 12" is the shortest spring length that I would go. Reliability could easily be an issue going shorter. Make sure the mag tube and follower is super clean. I use a product called Dricote its silicone free. Spray some down the tube, let it set a minute. Wipe it down with a clean, lint free wipe on a 12ga brush. Super slick, dry. Works for me
  14. Where are you staying? I might be able to help. All these sponsors are great! Should be an awesome prize table and match! Holiday Inn Sparta Fri,Sat and Sun Thanks
  15. chomp'n at the bit. looking forward to this match, still looking for someone I can ride with on Sat, coming in from Calif, wife will have the car visiting family up by Chicago.
  16. Winchester Ranger, is working and patterns well in my SLP,,, be advised the RIO does NOT fit in the AP Custom caddies, RIO's roll crimp is a taste longer than most.
  17. #13 & 14 http://www.calguns.net/caawid/sgflowchart.pdf
  18. Flying in from Calif. need some one that I can squad & ride with on Sat. Sunday I will be gtg.
  19. I'm looking for a 14", where'd you get yours? Direct from AP Customs
  20. I just got my pistons back from SRM, Super fast turn around. No springs,, no worries
×
×
  • Create New...