Jump to content
Brian Enos's Forums... Maku mozo!

69bowty

Members
  • Posts

    26
  • Joined

  • Last visited

Everything posted by 69bowty

  1. Apex has made a change recently to the semi fit barrels. I have 2 older M&P pros, got first Apex barrel a couple years ago and it wouldn't go in either slide. Had to remove material in every spot to get it to fit. Got a second barrel about 2 weeks ago and it dropped in without touching it.
  2. 69bowty

    Firing pin spring

    Wow! I had something similar happen on a 1911 only at make ready.
  3. 69bowty

    Firing pin spring

    I will check the pin length and confirm that it is ok. When I pulled the slide off at my club match the rear of the firing pin was flush with the pin retaining plate so the hammer wasn't hitting it. To get me through the match I stretched the firing pin spring and I didn't have another no strike the rest of the match.
  4. 69bowty

    Firing pin spring

    Yes, using the CGW extended firing pin.
  5. 69bowty

    Firing pin spring

    My SP01 Shadows has the CGW 11.5 main spring, their firing pin and spring. I've never had a light strike on any primers. Couple weeks ago at Area 4 i had 3 failure to fire on the first shot, it happened again last week at our club match. I was finally able to recover the round and there was no mark on the primer. It appears the firing pin spring was not returning the firing pin back far enough. I've never heard of anyone having that issue so thought I'd post it to help out. I've added the firing pin spring to the trigger return spring and slide stop in my repair kit.
  6. Any idea where to find one? I also suffer from small hands/short thumbs. I saw one on ipscstore.eu but nothing in USA.
  7. Does the mag release fit the SP01 Shadow?
  8. The benefit is you don't get bumped to open. The hammer must be all the way down.
  9. I use a silver sharpie
  10. More discussion here: http://www.brianenos.com/forums/index.php?showtopic=219790&page=1
  11. I have one on my 650, to get it to line up the bullet feeder is mounted to the left of the press. I'm using a strong mount, I used a piece of angle iron mounted in the same holes as the press do no drilling.
  12. The 2013 Sunflower Shootout will be held Oct 12 at Capital City Gun Club just west of Topeka, KS. All the match information can be found here: www.capitalcitygunclub.com/idpa/2013SS.html I would like to thank Brain for supporting the match and sending us prizes for the prize table.
  13. Here is a video of my M&P shot at 500 frames per second. The pistol is running a 13lb recoil spring. The load is 3.5 grains of titegroup under a 147 MG. I was pulling the trigger as fast as I could, no way I could out run the slide.
  14. I put one in my Pro, may having about 1 FTEs per match, none since installing the FRE through 3 matches and a couple practice sessions.
  15. I use the metalform mags in my Springfield 9mm 1911, none of them would lock the slide back out of the box had to tweak the follower to get them to work.
  16. If it was the same spring in the gun when I got it I'm pretty sure it was an 11lb or was wore out. The spring was an inch shorter then the new 13lb that's in it now. I haven't had any issues with either spring even with CCI primers.
  17. The light strikes in my pistol were only happening on one of my reloads. I am using a 124gr MG over 3.6gr Clays. I was getting primer flow which built up debris in the firing pin hole and caused light strikes. The issues was the light Ti pin and the super extra power spring were not supporting the primer when it got hammered by the fast burning clays powder allowing the primer to flow. Didn't have any issues with factory loads or my titegroup loads. Since switching to steel pin I've ran a thousand or so clays loads without issue.
  18. I had light strike problems on my SA 9mm 1911, replaced the firing pin with a standard steel pin and my problems went away. The pin in my pistol is a standard .063 dial 9mm/38 super pin.
  19. I also have the SA I shoot in IDPA ESP & USPSA SS, I have 2 loads I shoot, a 124gr MG JHP loaded at 1.090 OAL and a 147gr MG CMJ loaded to 1.10. I use both Tripp and Metalform 10 round magazines. I have had a couple FTF with the JHP in the Tripp mags after hitting the slide release on a slide lock reload. No issues with JHPs using the Metalforms. When new I did have some feeding issues, the groove in the extractor was so tight I would get 3 point jams I replaced it with a Wilson Combat bulletproof extractor and no problems since. HTH. Ty
  20. Seriously, though... What's the crowd like at Capital City? Being a complete noob, I don't want to end up in a place where I don't belong. If you've ever played golf then you know the guy who is on the first tee on a busy Sunday morning who has never played anything other than miniature golf That's what I'm afraid I'll feel like. It's pretty laid back, we have 3 bays we shoot in and 3 squads. Usually around 10 people per squad, good mix of shooters from D class to Masters. Here's the website: http://www.capitalcitygunclub.com/pistol/ccps.html come over and give it a try.
  21. We shoot at Capital City (Topeka) the third Sunday of every month.
×
×
  • Create New...