kfd147

Apex trigger and never look back.

Run it at a match. Get videoed doing it. Get suspended/banned for the travesty. 1 year later Wilson Combat will come out with a pistol with a comp. At that same time IDPA will do a survey on if the membership wants to use comps and what rules should be in place. 2mo later IDPA will update their rulebook.

Good Info! Thanks!

It does not effect the trigger pull at all. Sent from my Moto Z (2) using Tapatalk

Always glad to help. Sent from my Moto Z (2) using Tapatalk

https://dawsonprecision.com/dawson-precision-cz-75-p-01-fixed-competition-black-rear-sights/ Sent from my Moto Z (2) using Tapatalk

Slightly different cut over the rear. It will not clear the top rear of the slide. Use a P-01 rear instead. Sent from my Moto Z (2) using Tapatalk

Yes, I borrowed a buddy's large frame extension and it worked. Not pretty looking, but it works. Sent from my Moto Z (2) using Tapatalk

Did you shoot that at IDPA Nats? Sent from my Moto Z (2) using Tapatalk

Check and make sure the trigger bow spring screw is tight. Reduced or loose spring pressure on the bow will make the d/a pull shorter and short stroke the hammer. Jason

Oh and this should go without saying, but I have found that a few customers have done this and it caused similar problems. The magazine springs only go in and face a certain way in the mag tube. Jason

Ammo sounds normal then. Have you looked at the breach-face? Any burrs or is it rough and need to be polished? The firing pin hole may need to be slightly chamfered so the case glides over and doesn't get caught and take out a small piece of brass off the rim while going into battery. Anything to help the case to slide smoothly up behind the extractor helps. Other than that, i am out of ideas without having the pistol in my hands. Jason

Are you running factory ammo or reloads? That is something that you may need to look at too? Jason

Polish the underside of your slide and change the mag springs to Wolff extra power springs. This should alleviate the problem. Also check to see if you have any brass in your chamber. It doesn't happen often but a piece will get stuck and cause feeding issues. Jason

I've found the CZ Custom pads are easier to break down and clean in the field. Springer's have a small hex screw that can get lost and are hard to get apart. Jason

Double, yes.

If these two places don't have them, no one will. http://czcustom.com/new-firearms/cz-pistols-shadow-line/cz-75-compact-shadow-line-sa-da.html http://automaticaccuracy.net/?wpsc-product=cz-75-compact-shadow-line Jason

Is this on a Shadow or B series pistol? Jason

do you have to remove the bluing before putting this on?I sand blast or rough up the surface before I spray it on. Make sure you degrease the before you coat it.Sent from my XT1585 using Tapatalk

Cerakote Microslick. No need for a curing oven it just air dries. http://www.cerakoteguncoatings.com/finishes/C-110Q/micro-slick-dry-film-coating/ Jason

http://czcustom.com/cz-parts-all/czc-parts-made-in-the-usa/cz-75-full-size-grips-aluminum-blue-grip-tape.html https://shop.cz-usa.com/ProductDetail/19144_Aluminum-Grips-Full-Size-Blue-Czub https://shop.cz-usa.com/ProductDetail/19142_Aluminum-Grips-Compact-Blue-Czub Jason

It's a miss for each round in the black. You only score it if crosses into the down 0 or 1 scoring area on that target. Sent from my XT1585 using Tapatalk

Accu-Shadows and Target Shadows SP-01's (milled rear sight) are not legal in SSP. IDPA raised the weight limit to 43oz a few years back, so that is not a problem. A normal Shadow pistol tricked out is legal and very fun to shoot. Jason

Try using the screw from the rear sight and see if that works. Jason

There is a minimum, but no limit. Jason