Jump to content
Brian Enos's Forums... Maku mozo!

kfd147

Classifieds
  • Content Count

    206
  • Joined

  • Last visited

About kfd147

  • Rank
    Sees Target
  • Birthday 02/14/1972

Profile Information

  • Gender
    Male
  • Location
    Belton, Texas
  • Real Name
    Jason C. Armstrong

Recent Profile Visitors

676 profile views
  1. Yes, I borrowed a buddy's large frame extension and it worked. Not pretty looking, but it works. Sent from my Moto Z (2) using Tapatalk
  2. kfd147

    My P10C mods

    Did you shoot that at IDPA Nats? Sent from my Moto Z (2) using Tapatalk
  3. Check and make sure the trigger bow spring screw is tight. Reduced or loose spring pressure on the bow will make the d/a pull shorter and short stroke the hammer. Jason
  4. Oh and this should go without saying, but I have found that a few customers have done this and it caused similar problems. The magazine springs only go in and face a certain way in the mag tube. Jason
  5. Ammo sounds normal then. Have you looked at the breach-face? Any burrs or is it rough and need to be polished? The firing pin hole may need to be slightly chamfered so the case glides over and doesn't get caught and take out a small piece of brass off the rim while going into battery. Anything to help the case to slide smoothly up behind the extractor helps. Other than that, i am out of ideas without having the pistol in my hands. Jason
  6. Are you running factory ammo or reloads? That is something that you may need to look at too? Jason
  7. Polish the underside of your slide and change the mag springs to Wolff extra power springs. This should alleviate the problem. Also check to see if you have any brass in your chamber. It doesn't happen often but a piece will get stuck and cause feeding issues. Jason
  8. I've found the CZ Custom pads are easier to break down and clean in the field. Springer's have a small hex screw that can get lost and are hard to get apart. Jason
  9. kfd147

    Cz shadow compact

    If these two places don't have them, no one will. http://czcustom.com/new-firearms/cz-pistols-shadow-line/cz-75-compact-shadow-line-sa-da.html http://automaticaccuracy.net/?wpsc-product=cz-75-compact-shadow-line Jason
  10. kfd147

    Fitting a T-3 Disco

    Is this on a Shadow or B series pistol? Jason
  11. kfd147

    ReBlue-ing CZ Mags

    do you have to remove the bluing before putting this on?I sand blast or rough up the surface before I spray it on. Make sure you degrease the before you coat it.Sent from my XT1585 using Tapatalk
  12. kfd147

    ReBlue-ing CZ Mags

    Cerakote Microslick. No need for a curing oven it just air dries. http://www.cerakoteguncoatings.com/finishes/C-110Q/micro-slick-dry-film-coating/ Jason
  13. kfd147

    CZ 75 p01

    http://czcustom.com/cz-parts-all/czc-parts-made-in-the-usa/cz-75-full-size-grips-aluminum-blue-grip-tape.html https://shop.cz-usa.com/ProductDetail/19144_Aluminum-Grips-Full-Size-Blue-Czub https://shop.cz-usa.com/ProductDetail/19142_Aluminum-Grips-Compact-Blue-Czub Jason
  14. It's a miss for each round in the black. You only score it if crosses into the down 0 or 1 scoring area on that target. Sent from my XT1585 using Tapatalk
×
×
  • Create New...