Jump to content
Brian Enos's Forums... Maku mozo!

safenate

Classified
  • Posts

    195
  • Joined

  • Last visited

About safenate

  • Birthday November 6

Profile Information

  • Gender
    Male
  • Location
    Harpers Ferry
  • Real Name
    Nate Dudley

Contact Methods

  • Yahoo
    safenate

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

safenate's Achievements

Finally read the FAQs

Finally read the FAQs (3/11)

  1. Likes this...^^^^ Just picked up a MOS G34 for CO. What is the best choice going for optics? Heard good things about the window size on the Trijicon RMR but still undecided on power option and dot size. Thanks.
  2. Thanks to Dillon and those who recommended removal of rachet tab. I've lubed and adjusted so the machine runs now. The springs ( #13844 Short lever spring #13936 Tab/Spring Arm Spring) are in but after looking at them, do i also replace the cotter pin they both ride on? It looks that one of half of it is already broken off and trying to remove and rebend it may break it. Next issue: i'm getting both primers that aren't removed and then some primers that seat just before they are flush. Primers before I broke the rachet tab were seating completely (below flush). I did run one piece of brass all the way around the press solo, and it did fine. When I put in two in a row, the first one is not fully seated, but the second is... Any feedback is appreciated. Thanks all.
  3. I'm running some .40 S&W that barely makes Major with 155/165 & 180s. I may go with some 200s. Shot my first match with it the stock G40 and had my first malfunction with it. Is it possible to outrun this setup? Will the #20 still prevent damage from full house 10mm loads?
  4. Thanks dillon & punxsutawn. I'll call Dillon regarding the cleanup cost, but will likely spend the time to rebuild it. I like to know what makes things tick, but is more complex than the 550B I've been running.
  5. 550B, no case/bullet feeders, roller handle- From door to door (no previous setup), 300-400 per hour (9, .40, .45) Fastest time for 100 rounds, prepped- < 9 minutes. RL1050, TBD...
  6. Which springs should get replaced and how could I test them? What part number is the 'upper pivot pin'? Now the handle won't go beyond the horizontal position (doesn't pick up brass, etc.)
  7. I just started with my G40. Which rod did you go with? What sights are you running?
  8. Some pics are attached. Is that one part supposed to be scored due to contact? It appears that scored part has been beveled. Is that factory, or modified? Thanks for input.
  9. So, I've been a Dillon 550B owner since 2000 and have loaded 20,000+ rounds on it since then (mostly 9/40/45). Picked up a RL1050 around the new year from a widow who decided to finally offload it after it sat dormant since 2008. After adjusting the powder bar and overall length, I dumped some N350 and fresh primers. Enjoying a case feeder and primer pocket de-crimp was nice, but about every 10-20 rounds, the Primer Arm Cam assembly rotates out of alignment and the whole machine seems to lock mid-stroke, cause numerous issues (and frustration). In one such moment of frustration, the damn RL1050 Operator broke the Ratchet Restriction Tab into 2 pieces. A quick call to Dillon got a replacement part (plus a new manual and additional Dillon pieces) on the way. Can anyone explain the Primer Arm Cam rotation, stoppage issue and how to keep from getting double powder loads/unseated bullets and un-primed ammo? I'd like to churn out 9mm faster than the 550B, but may end up selling off this RL1050. I've heard other platforms are more complicated than the 550B and it may be beyond my mental capacity to operate such a machine. Thank you.
  10. I was really hoping to see a 1/8 at this link. Anyone know a company making a 1/8 308AR (16")?
  11. I put on a Faxon 18" 3 Gunner barrel a few months ago. It amazes many when they pick it up, very light with 15" Samson Evo FFT. That barrel shoots just over 1 MOA, after a full magazine dump, with bulk ammo. YMMV.
  12. I'm just looking into PRK surgery. Where did you have the surgery done, in WV? I'm near Martinsburg. How is the shooting going this far afterwards. I'm looking to have mine done in the late season, hoping to be ready by next season. Thanks.
  13. Another fan of American Select in 9mm loads. 8 lbs, 4.7 grains at a time, over a 115 MT JHP. Soft shooting and nearly fills the case before the bullet goes it. Fairly clean and softer recoil. Would get another keg for 9 minor. Think it would be above redline for 40 major. Would consider trying Promo for 40 major, given what is posted here. Maybe try E3 also.
  14. I've used American Select for 40/45, and 9x19 minor. Burnt up 8# & moved to the backup 8# of Bullseye. Also works for 38spec, 9 minor, 40, & 45.
×
×
  • Create New...