MAP

I have an Ammobot Rev.3 running a Super 1050. I'm planning on switching the 1050 to a CP2000 with the ammobot. Is this a direct swap or will additional Ammbot parts be needed? The Ammobot was manufactured in 09/2019 running software version 4.1.6. Any help would be appreciated. Photo attached of the right side of the Ammobot. Thank you IMG_8316.HEIC

I placed my order on 9/1 and received my Ammobot on 10/11.

In my view it is worth it. The Romeo 1 can damage easily.

The weight is pressed on. I payed it off easily. Mike

You will need to re-zero once the shroud is installed.

My personal experience with those primers is the same. They are very difficult to seat and, IMO, not worth the effort.

I asked at SHOT, they said 2019. I was hoping for much sooner. Mike

Rubber overmold

I spoke to one of the German engineers at SHOT. He indicated a long slide VP9 release at NRA and a factory extended mag laster in 2017. Mike

How will this apply to the Sig P320?

I spent 27+ years as an LEO in NJ between 1984 and 2011. AFAIK, NJSP never issued a .40 S&W pistol. Always 9mm. Mike

Did you have to down load them at all? Or charge for .355 work? I'm going to do all the typical load development anyways to see what shoots properly and what makes power factor out of this specific model anyways. Just curious as for a starting point.Sent from my LGLS991 using Tapatalk Same charge.

I've shot 8K + of the .357 Extreme 9mm through Sigs, Glocks and H&Ks. No problems at all. Mike

Uniquetek makes one. A bit pricy but it works well. http://www.uniquetek.com/site/696296/product/T1555 Mike

I believe that S&W does make 15 round magazines for the M&P.

I load the Xtreme 135 RNFP at 1.100. I get more consistent velocity and the same accuracy when compared to loading longer. With 3.7 gn of N320 I get 968.7 fps.

A piece of scrap wood and 15 minutes of labor.

At one time I had problems resizing 9mm case fired from one of my Glocks. I now use the Lee U die. Haven't had a problem in since switching to it. I have no personal experience with the EGW die. Mike

Can you please let us know of they shoot poa/poi? I find the stock sight on my 320C and 320F shoot high. Thanks, Mike

They told me the same. But, I though the sight cuts were the same on the 320 as the P series Sig's. ? I have one of Dawsons Charger rear sights for my 226 that I haven't put on yet, but if the cuts are the same why wouldn't it fit on the 320? I just installed an Ameriglo Sig P series rear sight on my P320. Sight installed with no problems. No overhang on the rear. Mike Oh yeah, i forgot about Ameriglo. What part # did you get. Also was the fitment tight, did you need to file it ? SG-402 plain black rear. Installed without fitting. Mike

They told me the same. But, I though the sight cuts were the same on the 320 as the P series Sig's. ? I have one of Dawsons Charger rear sights for my 226 that I haven't put on yet, but if the cuts are the same why wouldn't it fit on the 320? I just installed an Ameriglo Sig P series rear sight on my P320. Sight installed with no problems. No overhang on the rear. Mike

Using standard Dillon carbide 9mm dies I ran about 2% of my Glock brass that wouldn't resize properly. In a Dillon 650 I have a separate tool head with a Lee Universal de cap die in station 1, Dillon carbide sizing die (No de cap pin) in station 4 and a Lee undersized (U die) 9mm die (no de cap) in station 5. While more complicated, I've had zero issues since switching to this method. You can purchase a Lee undersized 9mm die fro Midway or EGW. Mike