-
Posts
1,877 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by Rolex
-
-
G43x and 48
in Glock
On 8/20/2021 at 11:57 PM, Malarky112 said:Just curious what’s your use?
Just target shooting- so lower PF reloads
-
G43x and 48
in Glock
On 8/20/2021 at 10:25 PM, Dirty_J said:Did not say it would not run- just looking for an option.
-
G43x and 48
in Glock
I shoot reloads only- PF 130- looking to replace the recoil rod and spring
to something around 15 pounds- stock set up is a little strong for a 130 PF
Any one change out these parts yet?
-
5 hours ago, vluc said:
Upgrading holosun from 507 to 507 acss Vulcan. Point being screwheads should not strip so easily.
Install on the plate calls for certain torque, and with the holosun design, the chps provided torque heads don't fit straight down.
AND- I have called and emailed them- NO response- the provided screws are to long- have a terrible head designed
compared to the factory flat head designed, so how long and what thread for the Glock 48 MOS slide? with their plate?
My other slides are milled direct- but just had to try the G48 MOS- with some regrets now because of screw length.
-
13 hours ago, Cuz said:
why do you need to keep removing the sight??? I’m getting ready to use red loctite on mine to keep them from loosening up. I wouldn’t plan to remove it unless it breaks.NO RED_
-
11 hours ago, chubs3a said:
I run the same set up and no issues here. Are you using the supplied screws that were in the CHPWS kit?
YES- silver color, not really a flat head screw, some said they are for RMR setup and not Holosun
-
I just got the plate for my G48 MOS and Holosun 407k x2 GR. The screws are too
long and hit the ejector rod!
Anyone else have this issue- PS just got it Saturday- and they where closed, so
ill call Monday and see what they say- also the screws are not black but silver!!
-
On 3/31/2020 at 1:38 PM, Bill H said:
I know this has probably been discussed in the past but I couldn't find it. Is the Talon grip tape good stuff? Is there something better? Rubber type or grit? It is for a Glock 17 for competition.
Thanks
Talon Pro Grip
-
Ghost
-
yes- but i could not order any- sat at at 5 MT the web page crashed- lost out again.
-
Finish- old ones could rust
And- some rattled when loaded to capacity, new ones will have tighter specs-
Not out yet- lots of us have been waiting for almost a year- for new product to
come out.
-
NO MORE BACKORDERS GEN 2 ON THE WAY
-
Great loss- to all of us.
-
On 3/26/2021 at 1:58 PM, WxGuy said:
Are you using a shock buffer on the guiderod? If you are, toss it. Maybe try a lighter recoil spring?
I have thousands in my S2 OR- with the buffer.
-
On 2/14/2021 at 4:59 PM, ltdmstr said:
Well, to state the obvious, everyone here is also looking for primers. Assuming they find some, what do you think the chances are they're going to pass on the opportunity and offer them to someone who just made your first post here? I'd guess the odds are pretty much zero. On a positive note, at the rate you're going your post count should enable you to try a WTB ad in the classifieds pretty soon.
-
On 2/16/2021 at 12:48 PM, George16 said:
The only only time my gas plug fell out was when it wasn’t installed properly. I didn’t make sure it “clicked” into place when I rotated it during installation.
Good thing it fell out when I was checking the zero since I just cleaned it. It fell out of the ejection port after I had shot about 15 rounds.
Remember last summer at SAPSA? I installed the gas plug but never turned it into battery, wife had interrupted me!!
We had to put new gas rings on it- lost that stage- but not the match!!
-
135 gr tc Blue Bullets Sport Pistol 4.5gr's OAL 1.130
-
Thank you G16-
-
I have SP on Glock and other mags- all have worked fine over the years-
-
Any one know the twist rate on the CZ Shadow 2 .9mm
Thanks
-
All you mentioned are very good and will work fin for you.
-
Blue Bullets 135gr TC run perfect in my CZ S2.
-
Grams- shooters connection or Ben Stoger
-
Not the best choice for major- HS6, CFE
MOS Plate issues.
in Glock
Posted
My G43X was cut for the Holosun 407k x2- has had 2k rounds through it- no issues.
My G48 MOS-has the same dot with a CH plate- so far- with 500 rounds through it
its still good to go- it will have more use in the next few months with training-