Jump to content
Brian Enos's Forums... Maku mozo!

Zachjet

Classifieds
  • Posts

    425
  • Joined

  • Last visited

Everything posted by Zachjet

  1. Which club is this. I need to make sure not to visit it
  2. Sounds like somebody was salty about a speeding ticket. Lol.
  3. I feel the same but about 1k21’s. I started pulling them out… have you tried the smaller decapping pins?
  4. I have a bunch for my pc9. I’ve never had issues as far as feeding.. I only have oem Glock mags
  5. 135TC out of my stock master.
  6. But if it’s not a Dillon does anyone really care?
  7. I’m going to PM you my number. I don’t articulate my cell very well on these forms but you seem like you were having the exact same problems I was which I have since worked out.
  8. First . Just to touch on that problem I had, are the primer and swag rods centered to the shell plate? Is it all brass Or just certain headstamp I’ve given up on 1k21/22 brass and I’ve been pulling them all
  9. I’ll be honest, I didn’t even check. I tossed them. As of now, with my current set up, the only brass I have an issue with is the 1k2x brass. I picked them and toss them because the primer pockets are just so tight
  10. That was range pick up brass, so who knows what shot it… honestly, if it doesn’t jam up the press, it doesn’t bother me.
  11. I just started using one It definitely doesn’t prevent all case bulging. This is three out of maybe 1500 or so
  12. My advice would be don’t use the automatic case feeder. And don’t use the bullet feeder. Figure out what each stage does by themselves and figure out what are the symptoms of something wrong. don’t have expectation of running 500+ rounds and hour until you figure out the machine. I think the machine it’s self is extremely simple. When you start adding 10 pieces of brass doing things, it gets complicated. also scrub the machine good when you first open it, because it’s coated heavily in anti-rust oil. And get an old toothbrush and clean the threads in the tool head good and this is the link to the bearings for the index arm. I broke one of them already. https://www.amazon.com/TRB-RC-6x19x6mm-Precision-Bearings/dp/B071D499GB?pd_rd_w=mAWSR&content-id=amzn1.sym.b854a5c2-4475-41f8-a6d4-df92b2868104&pf_rd_p=b854a5c2-4475-41f8-a6d4-df92b2868104&pf_rd_r=7TN5EXAR09JQ4S1WW5TC&pd_rd_wg=SAHzy&pd_rd_r=b9e47336-e6f7-42be-bb64-4b8933c84675&pd_rd_i=B071D499GB&psc=1&ref_=pd_basp_m_rpt_ba_s_1_sc
  13. I would think so because the tool head has 9x 3.5 mm jacks for the smart toolhead. and if anyone is having similar issues, feel free to send me a private message I’ll give you my phone number I know when I talk into my cell phone while working it’s not the most articulate writing.
  14. So after my wife purchased me an X – 10 for Christmas I set it up and mine had a consistent issue with flipping primers. Short version is that’s the primer pin wasn’t centered to the shell plate. Customer service was very good and they sent me all new small primer assembly and new pin out pretty quickly. I installed all the new parts and although the problem got significantly better, it still was not still not 100% right. After messing with the press this week I discovered that the swage Pin was making contact with the floor plate and causing the floor plate to clock a little bit and making the primer pin not be centered to the shell plate. I called them Tuesday morning, and I had new swage pin by Thursday night I got around to installing the new swage Pin and now the press runs like a top. Part of the reason why it took so long to figure out my problem is that I haven’t had much time to mess with it, being super busy at work. so now that I got her running right Im super satisfied with the upgrade from my hornaday LNL. That being said, I believe if I didn’t have the hornaday first I would have ripped this press off my bench and slammed it against the wall.. It’s a totally different feel from my LnL and a lot more going on with double the stages and I’m thankful I learned on the lnl Edit- to touch on the post above, I agree that the mark 10 is the bench mark for 10 stage presses. But I could not justify spending that much money. The way I see it is I’m all in with a bullet feeder, and floor plate for around 1500 bucks, not including the dies, which you need no matter what press you buy. So for the money I saved I could deal with working some bugs out.
  15. My buddy has the double stave RIA. He bought a whole new top end for it. Fits right on edit. A stock RIA upper
  16. I’m out. Most likely going to pull out of mid Atlantic as well
  17. We all joked that Frank was going to get removed somehow, someday. I guess they made their move. It’s a shame.
  18. I’ve ordered non-gun related stuff from them
  19. Yeah it is… in all honesty. I don’t see why you couldn’t cut down the keys feeder stand a little bit. I still haven’t gotten my bullet feeder to see if that would be a problem. It’s suppose to ship today/tomorrow
  20. So I completely forgot that my machine is a part waiting for replacement parts But from the top of my table to my ceiling is 4 foot that being said. My ceiling is unfinished and is just open. So maybe that’s why I can lift the lid to fill the case feeder edit. here is a picture I took when I first assembled it
  21. What are they going to say no they can’t move you and put you in open? Text the same amount of time as moving you to the proper division
  22. I’ll measure tonight when I get home. But it’s tall.. the post for the case feeder splits in half, so I put the case feeder on the post. Then connect the top of the post to the bottom half
  23. I bought a lyman universal hold down
×
×
  • Create New...