Jump to content
Brian Enos's Forums... Maku mozo!

bikerburgess

Classifieds
  • Posts

    1,554
  • Joined

  • Last visited

Everything posted by bikerburgess

  1. Sorry, didn't have time to go into it at work. Like others have said, burn rate, coatings, powder volume bullet weight, and many other things play into load development. Because a certain powder may burn at a rate that leaves some powder still burning as the bullet leaves the barrel does not mean reducing the amount of powder will make the load more efficient. Remember that a powder charge will have X number of individual powder gains burning at the same time to produce the gas (and therefore pressure) to propel the bullet down the barrel. Reducing the powder charge will also reduce the number of gains burning and the volume of gas at any point during the burn cycle, thus reducing the muzzle velocity regardless of muzzle flash. Sent from my SAMSUNG-SM-G935A using Tapatalk
  2. http://shop.springerprecision.com/product.sc?productId=257&categoryId=25Thus is the part in question yes it is a solid one piece replacement. Sent from my SM-G920V using Tapatalk So they call it a "EZ slide racker" seems like a stretch to claim is a firing pin stop when the manufacturer doesn't even label it as one. Sent from my SAMSUNG-SM-G935A using Tapatalk
  3. Send Troy McManus (DNROI) email dnroi@uspsa.org That said is the slide racker striker plate sold and labeled as a firing pin stop? If not I would highly doubt it's ok Sent from my SAMSUNG-SM-G935A using Tapatalk
  4. If it's like the Hornady then I would play with the position of the wiper springs and the center disk. I have a Hornady and it can fill the feed tube (spring) in about 1 minute. I can load 100 9mm in about 5 minutes without getting ahead of the feeder. Also it feeds faster with a pretty large pile of bullets in it, I normally put in just about as many as fill fit without spilling when I start. Sent from my SAMSUNG-SM-G935A using Tapatalk
  5. Just checked 1.3.14 and the add classifier button is there and it builds the whole classifier for you. I dont remember a android version without it but I have only been using it for a little over 2 years.
  6. This fix has been working great for me for the last 1500 rounds. The rod is a piece of welding rod I put through a hole drilled in the bowl (right now it's just taped in place on the out side) it stops a second case from being able to make it around to the drop window so only one case can drop at a time. The sheet metal ensures that no cases ride over the rod and also bumps and upside down cases out of the notch in the case plate. Between that and adding a brace to keep the feeder from moving around as I run the press, I haven't had any jams since I added the rod (I had the flipper and brace for a while but I was still getting jams every hundred rounds or so) Also with this set up I was running 500 ish cases at a time in 9mm or 38 sort colt as you see in the picture Sent from my SAMSUNG-SM-G935A using Tapatalk
  7. That can happen because in the high hit factor on each stage changes when you look at it in combined or division specific results.
  8. Ar15sport.com Is a small shop that specializes in A1 parts. If it's available John has it or knows where you can get it. If it isn't on his web site call him and he will help you out Sent from my SAMSUNG-SM-G935A using Tapatalk
  9. The real answer to the question is no but the perceived advantage would make it into a custom 2011 division like Limited and Open. When Ben started wining Nationals he was in the minority shooting DA/SA guns now that everyone has jumped on that band wagon plastic is the minority. I have watched shooters change from GLOCKs to CZ and never reach the same match performance with the CZ that THEY had with the GLOCK, I';m not saying one is better than the other just that some shooters will perform better with different pistols. Unfortunately (unless you are a gun seller) many(most) shooters do not experiment scientifically to see what truly works better for them, or practice with what they all ready have to get better, they instead buy whatever the new hot pistol is.
  10. Just to be clear, "All the top dudes" does not include 2nd and 3rd at last years Nationals, I believe the difference between first and second was ONE charlie out of 408 rounds
  11. Yes, i just run it the whole time Sent from my SAMSUNG-SM-G935A using Tapatalk
  12. I ran a stage at one of my club matches that was just 1 popper, I get requests to do that again than any other stage I have run (the One popper was at 80 yards I think that kept it interesting)
  13. I have one on a G22 with a 9mm conversion barrel. I really like how it fits to the slide (the back of the comp is contoured to fit over the bull nose on the factory slide) so far I've only run minor in it, with a 11 lb spring it runs 100% with my 124gr production load. Tried it with some hotter long shot loads and it was super soft but my wife had a few FTE with that load. Sent from my SAMSUNG-SM-G935A using Tapatalk
  14. Ultimately, I don't care what a MD wants to incorporate into a stage. Just don't tell me that simulated land mines are practical and expect me to agree. Only things you see on the way to work or going to the grocery are... practical? What if they were snapping turtles? Honey badgers? Pressure cookers? Your kids toys on the floor while an intruder is in your house. Or the dogs squeaky toy that gives away your location.In fact, squeaky toys would be fun! Kids toys? that would have to be Logo's and you would have to be bare foot. no penalty for stepping on them other than how much it hurts affecting your stage plan.
  15. Actually that is wrong. Inertia guns need solid resistance to run. You can in essence induce malfunctions just like on pistols by limp wristing or limp shouldering. (not firm enough.) correct me if I am wrong but on an inertia gun when fired the bolt carrier remains in place (due to inertia) as the rest of the gun moves backwards under recoil compressing the spring in front of it then as the gun decelerates from the initial recoil impulse the compresses spring pushes the bolt carrier to the rear cycling the action. https://www.youtube.com/watch?v=BEA2yRC9Qb4 putting a gun against a post seems like it would stop that initial rearward movement enough to cause issues. yes having a really weak hold could cause issues with the rest of the cycling action, A post is not the solution.
  16. Putting a inertia gun against s post it's the exact opposite of what it needs to function. The gun must move during recoil in order to work. Try holding it softly and see what happens Sent from my SAMSUNG-SM-G935A using Tapatalk
  17. I normally find the S+B ones about half way through the sizing die. I hate to admit I usually just keep going and they load just fine Sent from my SAMSUNG-SM-G935A using Tapatalk
  18. I have and do play in all the Divisions, I have a cheep GLOCK I built to play in open, as I have a weird thing for cheep guns. Open division can be a different game than the iron sighted divisions, it is so much more about going fast than even limited that it brings a whole different aspect to the game. Did I stay in open? well I have not really stayed in any division because I like guns and want to shoot them all (I have shot every handgun I own in competition, Speed Steel, IDPA or USPSA) Yes Open can be expensive but it can also be a lot of fun, I just like change too much to stay in one division.
  19. If you want to shoot single stack just compare your scores to the Production shooters the two platforms are very close in performance.
  20. No, it doesn't. There is a rearward force exerted by the case on the breach face, and a forwards force exerted on the barrel by the bullet. Those forces are equal until the bullet leaves, at which point recoil begins.How does your theory explain the function of blowback pistols? In a blowback design there are no locking lugs and the barrel is rigidly attached to the frame. It's not a theory, it's physics. In a blowback gun there is a rearwards force against the slide. Because the slide is not locked to the barrel, and the barrel, attached to the frame, is being held by the shooter, the slide begins to move immediately, with movement damped by slide mass and spring weight. With a locked breach firearm the rearward force on the slide is cancelled out by the force on the barrel because they are locked together. You may want to watch the above video before you dig into your position that the slide doesn't move until the bullet leaves
  21. Unlikely, heavy bullets hit higher in revolvers as well and Revo barrels are fixed to the frame.That was not the case in this instance, I am used to and have observed POI changes with different bullet weights and velocities in this and other guns, this was WAY outside that range, if I recall correctly it was about 8" higher at 10yd than a similar PF 147gr loadSent from my SAMSUNG-SM-G935A using Tapatalk
  22. And the whole list got scraped with the 2014 rule book not the 2009 one Sent from my SAMSUNG-SM-G935A using Tapatalk
  23. Playing with heavy bullets in a Tanfoglio 9mm (170gr) I ran into a load that hit very high, compared to the lighter bullets. best I could figure is the bullet was still in the barrel when it started to unlock from the barrel. Sent from my SAMSUNG-SM-G935A using Tapatalk
  24. Love hearing this. I get frustrated at matches when I run across an RO who gets cagey when asked to clarify the 180 on a particular target from a particular position. Happened most recently at a small major. Squad was trying to get a better handle on the 180 for a target at the start of the stage. It took way too much effort on our end to get more than: "Just don't break the 180 and you'll be fine." Makes me really appreciate the ROs who are confident enough to help a squad understand what is and isn't a safe shooting position. When asked about the 180 on a target, I will always say if it is down range of the position asked about. I Will Not say "your fine shooting it from there" or "you won't be breaking the 180 there". I've seen the argument erupt after a run when the competitor gets DQed and says you said it was ok from here! When in actuality the shooter over swung the target and broke the 180.Targets are either up or down range from any location, and that is not the same as where you point your gun. Sent from my SAMSUNG-SM-G935A using Tapatalk
×
×
  • Create New...