wisconsin

I've read past posts on cleaning finished round in our case cleaners but all the responses seem to be geared for jacketed ammo. Since lead bullets use wax type lube, even keeping your die clean of excess lube some still gets onto the case. In my case I'm using a RRA wadgun. Any excess bullet lube on the finished case will FF sometimes because of the tighter tol. in the gun. Soooo does anyone here run there finished lead rounds through their case vibrators? I tierd of cleaning the finished rounds with a 3M pad. Jeff

Does anyone here use these for Bullseye?

Today I did. Used both the barrel and the case check. 99% of all reloads went up to the edge of the barrel hood and flat to the top of the case check gauge. I find that on this RRA the tol. are tighter and .468 works better. Now that with my buddies rounds. .470 on my reloads might be part of the problem. No round moved on either .468 or .470 with your test. In regards to the recoil spring. I thought the same thing. If the round goes into battery by me releasing the slide. And has no failure to eject. But the next round fails to feed all the way in (1/8-3/16"). Maybe he changed the factory supplied #11 spring with say a #8 spring to get it to work with his bullseye reloads. I wish there was a way to test a spring to see exactly what # it was. But I do have some Wilson springs I can test it with. I will give that a shot and see what happens. Jeff

The Redding comp die has no die plug. My dillion die does. But I'm not using it for these loads

I changed to a Redding, competition, seating die for all my pistol calibers, and no longer have those issues. I'm using a Dillon 550B. I do use the Redding also. I was just wondering if the die hole is lined up right with the shell plate

I'm using a .452,200 gr lazer cast LSWC,4.0,4.6, 5.2 gr.W231,1.250 col, .468/.467 taper crimp,all rounds passed the case gage test, #11 factory spring. When I seat my bullets there is a slight case buldge around the bullet. This is on all my reloads. And I believed this to be the result of the .452 bullet. It has never been a problem for my 1911's until today. I just bought a used RRA wadgun, cleaned it, oiled it etc. When putting the first round into battery it went in no problems.Firing the gun the second round didn't go all the way in.This continued to happen until a buddy of mine handed me some nickle plated cases with the same round in it/no case buldge. No problems. My question is? The press I use is a Dillion 650. Could my toolhead be off enough that my rounds aren't getting seated right? Jeff

If you have two powder measures swap the one you are using on the .45 for the one you use on the other calibers. Geeeeeeeeeeez . I never thought to do that. Yes I have seperate setups for the 38/357 & 9mm. Will swap one of the powder systems with the 45 acp bars and see what happens. Sometimes I feel so stupid. Will see if the problem goes away. Thanks. Jeff

Case lube is not the issue as the case has already come off the flare. Its when the failsafe rod pulls the bell crank plates. The powder bar seem to be hanging up some how. The failsafe rod is doing what its suppose to do. Its the powder bar that seems to want to pop forward every so often. And I do mean POP forward.

Yes I'm sure

Thanks but all is installed proprely according to the directions. Believe me I've spent countless days watching it cycle and making absolutly sure everything is running right according to the 650 manual. I even took measurements off of my 9mm and 38/357 conversions to see that they all match my 45acp setup with regards to the manuals instructions. This is driving me to drink. But I still love my press. Jeff

I'll try to make this short. I've had a problem since day 1 with my 45acp setup that came with the press. Dillion has been called 3 times over the 2 yrs I've owned it on this. On the forward stroke at the point where the only thing that needs to be done is the failsafe rod pulling the powder bar back to the next powder drop position. Every 10th or so round the powder bar pops forward so hard that primer are turning side way and upside down also powder is jumping out of the powder check station. Like I said it is the only funtion left to be done with the handle 3/4's of the way forward. Dillion thought the first time it was cause by me using new and mixed brass with regards to the flaring bell but the case has already come off of the flare. Next it was the failsafe spring should be tightened half its width. Next they sent me out a new powder bar assembly because it was thought the thickness of the bars where to much. I come to find out today they are with in the thickness they should be. I have cleaned the bar and track it takes and emery cloth the edges and flat spots. I also tried silicone grease on the leading edges of the bar which did work for a 150 rds then the problem came back. I'm in no way mad at Dillion they have tried to solves this problem for me. But that is kind of hard for them to see what I see. Has anyone else had this problem if so I could use the help. This last reloading session was less than enjoyable. Jeff

Can I PM you? Jeff

Is there a sight that deals with hard to find firearm parts. S@W has few parts for this pistol. I'm looking to stock up on needed spare parts just in case. Jeff

AHHHHHHHHHHH! I see that would make sense. This pistol is very accurate for it size. But the one thing I didn't do was other than the 148 HBWC is try 140fp or 158swc weight bullet. I try not to post "please help" unless I've tried just about everything I can to get results. This grasshopper thanks all of you for your help. Jeff

I will try and keep this short. I've messing around with this for almost a year. I'm reloading for this pistol and using 125 gr. fp,hp with W231. 3.8-4.4 gr the oal come off of the winchester powder sight so I'm sorry for not remembering it off the top of my head. If I use 148 gr hb wad cutters lead or berry/3.8 bullseye flush to the case the shots will group dead on at 7-10 yds. If I use the 125gr. bullets they will all group 6-8" low holding dead on off of sand bags. No matter what I shoot in the w231 3.8- 4.4 gr range it won't matter hp or fp they all group low. Nice tight groups but low. What in gods name am I doing wrong. Jeff