Search the Community
Showing results for tags 'recoil spring'.
-
Trying to figure out the recoil spring tuning. Any information would be appreciated. My understanding is the lighter the bullet the lighter the spring? 9 mm 115 should be 10 lb spring 147 should be higher? Or am I misunderstanding this?
-
This is going to be a multi video process. Stay tuned for further videos. They can also be viewed on my Youtube Channel. More videos to follow shortly 3. Removing The trigger bar and trigger assembly - (SEE ABOVE FOR POLISHING) 4. Removal of stock staked trigger pin 5. Installation of CGW reduced power trigger return spring and CGW floating trigger pin 6. Reassembly 7. Testing
- 26 replies
-
- cz shadow 2
- optic ready
- (and 12 more)
-
I have a 1976 Tanfoglio P19 Combat and wonder what recoil spring weight would be proper. This gun's specs differ from the ones I can find for later Combat models on the internet. For example, the gun weighs 950 grams instead of 1150.
- 2 replies
-
- tanfoglio
- recoil spring
-
(and 1 more)
Tagged with:
-
Hi guys, I'm looking for a little guidance please. I had my Shadow 2 slide milled for optics and to make CO weight by Primary Machine. I'm thrilled with the results and the gun is only 43.1 oz. I'm running the same 10# recoil spring as before the slide work. My load is Federal Syntech 150gr. Now, there's a bit more snappy recoil than before. Do I go heavier with the recoil spring? Or lighter? (yes, I'm gripping it harder )
- 10 replies
-
- shadow 2
- carry optics
-
(and 1 more)
Tagged with:
-
Thinking about changing out the stock recoil spring on my 40 cal Edge with a 12 lb one to keep the muzzle from nosediving so much. Any thoughts? Thanks, Darrell
- 18 replies
-
- recoil spring
- edge
-
(and 1 more)
Tagged with:
-
So, Gun came with 3 recoil springs. Choose the middle one 12, something LBS and feels good. My Brass is flying 10 to 15 feet however, is this a bad thing? Should I reduce recoil spring? I've read that 6 -7 feet is optimal? Help greatly appreciated...
- 9 replies
-
- lim custom .40
- recoil spring
-
(and 1 more)
Tagged with:
-
i recently bought a smith & wesson sd40 ve and did not really like the plastic guide rod, i have always had metal guide rods before so i purchased a aftermarket stainless steel quide rod with 15lb recoil spring. i know the oem spring is 18lbs but i figured if i used a lower grain rd like a wwb 165gr fmj it may lessen the recoil and get back on target by cycling faster. am i correct in my assumptions? if not what ammo do you think i should use with that setup? or should i just switch the oem spring onto the steel rod?
-
I purchased an Apeiro in .45 acp. I wanted to go with a Dawson tool less guide rod. The question I have is what strength of recoil spring should I use with the Apeiro? I will be shooting factory 230 ball ammo to start with and because of the island barrel there is a mass difference. Just looking for some input.
- 3 replies
-
- recoil spring
- apeiro
-
(and 1 more)
Tagged with:
-
I've got a problem with my 10mm Witness Elite that I've not seen referenced anywhere. I load 180 JHPs to 1250 fps and am using a Wolff 20 lb recoil spring and a 22 lb hammer spring to try to control the slide velocity. I also welded up a FPS and created a flat bottom FPS but that didn't help much. Seems the FPS hits too high on the hammer to have much effect by using a flat bottom. So here is my issue. When I swap out my 40S&W barrel to 10mm, I install the 20 lb recoil spring on a Henning Conefit guide rod. Except the spring is almost impossible to install. It doesn't want to clear the edge of the dust cover unless I hold my mouth just right and rotate the spring in incremental steps until it finally just squeezes in. I'd like to go up to a 22 lb spring but if I have this much trouble with the 20 lb, I don't think I'd be able to get a larger spring in no matter what I do. I have no trouble with the standard recoil spring for the 40S&W, by the way. Is anyone else having this problem and, if so, what did you do about it? I'm thinking of taking my Dremel to the dust cover and sanding a slight bevel on the trailing edge where the spring slides under to see if that helps. Ideas?
- 5 replies
-
- tanfoglio
- recoil spring
-
(and 1 more)
Tagged with:
-
I'm left-handed at 10 yards my quick second shot was lower right compared to the first shot. 14 pound hammer spring 10 pound recoil spring.
-
What lb recoil spring are you all running in your XDm's. I will be loading 180's to major. Thanks
-
Does anyone use a recoil Buffet? What weight recoil springs do you use with a 134 PF?
-
I'm going to buy a SS guide rod and reduced power recoil spring 13# or 14# in my Glock 34. I have never done this. Do I need to get a lightened striker or lighter striker spring to counteract that? Or will the stock ones be sufficient? I shoot 124 gr manufactured ammo if that matters. Thanks.
- 5 replies
-
- recoil spring
- striker
-
(and 2 more)
Tagged with:
-
I won 500 rounds of Ibeji moly bullets, so I got a 500 pack of their 230gr RNs. This is my first time to use moly - usually, I go with Xtreme plated, but since these are free... So for those using moly, what is your powder of choice? While I'm asking - did you change your recoil spring to accommodate the load? (currently using an 18 or 18.5) Of course, the end goal is to find a load that makes Major and groups well. Thanks in advance!
-
What weight recoil spring is recommended for your basic competition 200-230gr loads? I have noticed that my slide is much harder to rack compared to others I have felt.