Jump to content
Brian Enos's Forums... Maku mozo!

MeatPuppet

Members
  • Posts

    39
  • Joined

  • Last visited

Profile Information

  • Gender
    Male
  • Interests
    Alcohol inventory reduction specialist
  • Real Name
    Steve O

Recent Profile Visitors

564 profile views

MeatPuppet's Achievements

Looks for Range

Looks for Range (1/11)

  1. Graf and Sons had it last week. Snagged 8lbs-N330, 8lbs-N340, 8lbs-3N37 and 8lbs-3N38. Prices were reasonable, $278 for each 8lbs (2 x 4lb containers). $20 Hazmat and $10 shipping. The "in stock notification" signup stinks and I never get alerts. I check it 10 times a day and happened to strike gold. Besides 9MM, I load for some larger bore suppressed and the VV powders burn super clean. Totaly worth the money.
  2. I have the 6 MOA on a milled Shadow. Huge difference. I actually prefer it to my other Shadow with an SRO. Only 2500 rounds on it, so I cant comment on reliability.
  3. I never experienced that much variation. I was loading 147gr to about 132-135 power factor and never had different lots fail to make power factor.
  4. Prima V is the bomb. A lot like VV N320. But there were variations in velocity Lot to Lot. Luckily I bought in bulk. Still have 30lbs left.
  5. I had the same experience. Super 1050 with Ammobot loading 9MM when... BLAMMO! Next thing I knew, the primer follower rod and 458 SOCOM case as a follower rod weight were sticking into the ceiling like a crossbow bolt. While disassembling the primer system I think I discovered the chain of events. Primer detonated while being inserted in the case (don’t know exactly why), the yellow primer dust that I had never cleaned up ignited and then the primers detonated. Subsequent “Google-Foo” revealed I should have been cleaning off the yellow primer dust with Isopropyl alcohol. Only damage to the press was replacing the Primer Feed Body Housing and Early Warning Buzzer.
  6. Cha-Lee made mention of them about the time I became dissatisfied with the Acme 9mm quality control that I had been shooting. Nothing but good times with the Eggleston 124gr so far. As a bonus, you can get them in 356/357/358 dia. The coating has always been perfect and they feed 100% in my Mr. Bulletfeeder.
  7. Everglades Ammo special pricing going on right now: CCI #500 Small Pistol Primers: $26/1000 CCI #400 Small Rifle Primers: $26/1000
  8. Yep... Gets hot after the first few thousand rounds. I suppose thats why they recommend putting a fan on it. It has worked out fine for me.
  9. Make sure the Dillon swage station is set up right. I had to use a Dremel cut-off wheel and slice a case in half to see that the Dillon Swage Hold Down Die was not supporting the case web as the swage rod pushed up. This allowed the web to flex upwards when the swage rod pushed up. If there was a smushed primer, the flex was enough to allow the plate to index without sensing the smushed primer. Once adjusted, it works pretty good.
  10. Dont worry about it. It is normal. I went from a Dillon Square Deal directly into a 1050 / Ammobot setup. I had the same reaction as you and did all the things you are describing. I went so far as to replace the three roller bearings in the Dillon lower unit. It smoothed things up, but I still had a "hitch" that felt like something as binding up when manually cycling. Now I am used to it and it does not bother me any more. I ment to email Ammobot customer service and ask it it is a side effect of the electric motor not being powered up when manally cycling. Some kind of sciency-thing with the induction motor thingie. Fire that pony up, sit back and enjoy the ride!
  11. Well, yes. I have an audible alarm system. Essentially it is a loud "Bang" at the primer seating station. Twice followed by a chain reaction of the remaining Federal primers in the tube. The swage station usually locks up the shellplate on a ringer and the Ammobot stops after sensing the resistance. Ususally. To be fair, I have only had a few ringers in over 70K loaded last year (amazing how many friends you suddenly have when you get an autodrive). I only learned about cleaning out "primer dust" after my first detonation, got lazy and re-learned it after the second one. Spectacular! But not really something I worry about. The Super 1050 is a great machine, but when you add an autodrive you start expieriencing problems that the machine was never designed to handle. Aftermarket parts definately resolve a lot of them (F&FB, Level 10, etc...)
  12. I have a 1050 toolhead I use for just processing 9MM brass. (1) Lee Universal Decapper (in place of Dillon) with Squirrel Daddy decapping pin. (2) Dillon primer pocket swage station (3) Empty (typically primer station) (4) Empty (typically powder drop) (5) Dillon Size die with decapping pin removed (6) Empty (7) Lee U-Die with decapping pin removed I use the F&FB heavy duty shellplate, Level 10 shellplate bearing upgrade and the Ammobot autodrive. I can process brass at around 2000 pieces an hour with this setup. Pre-processing my brass definately helps when doing long runs of loading.
×
×
  • Create New...