400driver

I had the DA case feeder for my 650. I used it for about 3 months, sold it for a small loss and then got the Dillon case feeder. I think that is what will happen after you have had yours a while, it's good but the extra investment is worth it. Sent from my ONEPLUS A3000 using Tapatalk

Lot of my friends case guage and then only put the failed loaded rounds through the GRX. Guess it saves a lot of time versus pushing each case! Sent from my ONEPLUS A3000 using Tapatalk

So just cut the wings off completely? Sent from my ONEPLUS A3000 using Tapatalk

I already have a small screw tapped into the side frame which controls the pre travel. I can just turn the screw and it changes instantly the position of the trigger. Sent from my ONEPLUS A3000 using Tapatalk

Will have a look at it. Do you know if the disconector is needed for single action only? Sent from my ONEPLUS A3000 using Tapatalk

Ok. Just replaced the CGW sear for the original sear for a big competition at the end of the month. As the sear clears the hooks that would suggest that there is enough over travel. I will wait till then to give it a try. It's adjusted perfectly now and has virtually no over travel after the hammer drop. It is an incredible pistol, glad you like it. Sent from my ONEPLUS A3000 using Tapatalk

This is the Shadow Viper. Sent from my ONEPLUS A3000 using Tapatalk

Viper is a CZ Shadow with a 6 inch slide made by a German gun maker. Sear is the same as a shadow. Not sure it is that as you can continue the trigger pull into the original double action. Will give it a try though. Sent from my ONEPLUS A3000 using Tapatalk

Have a Shadow Viper using a Cajungunworks competition hammer that has been an incredibly accurate gun. After much use the sear is getting a small amount of wear as it rubs against the harder hammer. The gun is a target pistol and is used only in single action. I installed a CGW billeted sear to match the hammer and the problems started. On trigger release the hammer would fall a short amount and would not drop completely. The sear clears the hooks but does not make it all the way down to the firing pin. Could it be that the hammer is interacting with the wings of the disconector ? In single action, do I even need the disconector installed. Here is a link to a you tube video of what happens. I would be really grateful for any suggestions about fixing this problem. I have reinstalled the original sear after stoning out the slight rounding of the lower sear edge. I would like to have the CGW sear as it will reduce the wear over time. The trigger is incredibly crisp after stoning the curve and remains so for a few thousand rounds. Thanks Mark Sent from my ONEPLUS A3000 using Tapatalk

I had trouble with the website and my phone but using Chrome allowed me to complete the process. I used Google translate to email him. Give it a shot!

http://www.armeriapatria.it/index.php?main_page=product_info&cPath=21&products_id=162 Thats where I bought mine. 170 Euros plus postage. Speedily posted out,well packaged. Add it to the cart , go through the process and they will email you with a price for shipping. For those outside of Europe , Transferwise makes it very easy to make a payment to his bank in Italy. Took me less than 5 minutes.

I have also but its too difficult to say that my accurate throws are down to this alone. I suspect it is a combination of all the tweaks that I have done. I am sure it cant hurt and took only a few minutes.

Got mine today and tried WSP to start. A few of my Dillon tubes did not enter the Delrin holder easily and I had a few " stalls" of the tube filling. A few turns in a drill and they entered perfectly and this seemed to solve the problem. Its nicely made but I cant help feel it is just a very nicely made Vibraprime. There must be a company that can manufacture a similar product as a price between the Vibraprime and the PAL!

I splurged and bought the micrometer from Uniquetek and have not regretted it. I switch between loads and find it to be a great product. It proves the old adage of buy cheep, buy twice. Sent from my ONEPLUS A3000 using Tapatalk

Don't buy the Prarie Dog version. There is more play than the original Dillon item. I managed to make mine useable as it was outside the return period by winding thin copper wire near the C clip attachment. That made the slop less. Sent from my ONEPLUS A3000 using Tapatalk