THEMULE

Again thank you for the help. It seems to be resolved. The back bottom corners of the trigger bow were hitting the frame. A bit of sanding fixed it right up. Sent from my iPhone using Tapatalk

You should be looking at sti dvc open. Sent from my iPhone using Tapatalk

Yep that’s how I checked it. I think I found the issue. I pulled the grip safety and very slowly cycled the assembly. If I pull the trigger just enough to release the hammer it will catch the half cock, with just a slightly more firm pull it misses the half cock position. I believe this would be caused by the sear angle being incorrect and basically just barely sliding off of the hammer engagement as opposed to “breaking” that engagement. Does that seem reasonable ? Sent from my iPhone using Tapatalk

Thanks for the responses. I’m going to go check for the clicking sound and the mag release clearance now. The gun ran previously with an sti trigger then a modified svi trigger. I’ll let you know what I find. Sent from my iPad using Tapatalk

Just put a new trigger in STI 2011 and it is intermittently catching at half cock. It is not hammer follow as the gun is still on the bench and has not been shot. I have tried backing out the over travel screw with no success. I've tried increasing and decreasing the sear spring pressure to no avail. I'm at somewhat of a loss as to what to do next.

While I have not had any negative experience with freedom I have I’ve witnessed 2 different people/weapons that had issues with it in .223 and since that I’ve stayed away from it. The people supporting freedom and white box do you know how tight the chamber is in your pistols ? I have to reject anything that is on the tight side of a Dillon case gauge. Sent from my iPhone using Tapatalk

Thank You Sent from my iPhone using Tapatalk

I’m in the process of moving and my press will be packed up for a considerable time. I normally run long loaded .40 ~166-167 pf 180gr. I haven’t had any feed issues with factory length ammo in my STI’s. Does anyone have any recommendations for inexpensive practice/match ammo that performs. Sent from my iPhone using Tapatalk

I like and am using Uncle Jerry's comp, The Titan has it's uses though, keeps pesky RO's out of personal space and gives your video a dynamic shake for each shot. HaHa. I've heard good things about Robbie Wheaton Comp but haven't had a chance to test one.

I enjoy shooting SC, trap, and skeet traditionally but am looking forward to doing some report pairs with match saver and loading on "pull".

HaHa, I tried that last year and found out I couldn't. HaHa Had a great time though.

I didn't receive a receipt. Or the normal Practiscore Thank You for registering email. I've registered for matches before and after without issue. I only looked on the match page, and didn't see additional contact information. From first post I don't really use or check Facebook either. I was exploring other options as I sent an email on 9/22 and 9/26. Thank you for the response, I'll wait to hear from you. UPDATE- Mr. Horner contacted me, so the issue will be resolved. Thank You.

Has anyone found a way to contact match administration ? I signed up at the same time as the group I wanted to squad with and have been charged for the match. I received no emails or additional information following that. When the rest of the group received the squadding info, I sent and email to to the contact on the website main page, received no response. Waited 2 days and sent another email, no response. Sent Mr. Horner a PM, received no response. Who do I need to contact and how ? I should be in the match, but I understand glitches happen. There needs to be contact from the match administrators though, as they accepted payment.

WHAT ? It's not on a named road, we're screwed. [emoji3]

I have a similar issue, except I'm not running an auto drive so the press just stops on the index stroke. If I'm really moving the case pops out but usually just stop and push the case into the shell plate. There isn't a catch with my case feed and I'm using a Dillon shellplate. I haven't looked into it any further than bump the shell back in and continue. I generally load any brass that comes my way and it might happen 5-6 times a thousand. It seems to be every now and then the shell just hangs up and doesn't fully enter the shell plate. The timing at that juncture is fairly important as the shell plate is moving, as your video shows. I did however just load 1200 new Remington brass and I don't think it happened but might of once. Sorry I can't be of more help, but it's not as frequent for me and I just stop.